manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Руководство по обслуживанию

Поделиться
Скачать
EFI FIERY X3eTY 35C-KM Скачать руководство пользователя страница 73

65

The troubleshooting process

Printing

N

OTE

: 

Intermittent print quality problems are difficult to trace. Before you try to troubleshoot print quality problems, print a test page 

to make sure that the copier itself does not need servicing or adjusting.

Test page fails to print

Print engine is not ready 
to print

1. Make sure the copier is powered on and ready to print.

2. Check the copier Control Panel for indications or messages about the 

copier status.

There is a problem with 
the connection between 
the Fiery X3eTY and the 
copier

1. Make sure the Fiery X3eTY power switch is in “On” position.

2. Power off/on the copier.

3. Make sure the Network Scanning option is available from the copier 

Control Panel. 

4. Check again that the copier interface cable is present and properly 

connected to the Fiery X3eTY and the copier. 

5. Check again that the copier interface board is present and properly 

connected to the motherboard. 

6. Replace the copier interface cable.

7. Replace the copier interface board.

8. If the problem persists, service the copier.

Corrupted system 
software

Reinstall system software.

Faulty HDD

Replace the HDD. 

If replacing the HDD does not correct the problem, make sure you install 
the old HDD back in the Fiery X3eTY.

T

ABLE

 A

Fiery X3eTY error conditions (Continued)

Symptom

Possible cause

Suggested action 

Содержание FIERY X3eTY 35C-KM



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды