EDWARDS SYSTEMS TECHNOLOGY EST2, Инструкция по установке

Страница: 118 / 120

P/N: 387207 REV: 2.0 Page 2 of 2
S1
Group number Output addresses S1 dip switch settings Module
1 2 3 4
1 01-08 on off off off 2-SANCOM
2 09-16 off on off off SHO-4
3 17-24 on on off off SRU-8
4 25-32 off off on off SWU-8(/3)
5 33-40 on off on off SWU-(8/3)
6 41-48 off on on off
7 49-56 on on on off
8 57-64 off off off on
9 65-72 on off off on
10 73-80 off on off on
11 81-88 on on off on
12 89-96 off off on on
ON 1 2 3 4
To set the dip switches:
A. Configure the SAN-CPU in the system programming utility.
B. Note the in the programming utility (09
to 89).
C. Set the dip switches on S1 to the group number of the SRU-8’s start output
address.
start output address of the SRU-8
Set the SRU-8 dip switches. 3
Remember that the SRU-8:
Cannot occupy the 2-SANCOM addresses (01 through 09).
Requires one output address group, which consists of eight
addresses.
INSTALLATION
FIELD WIRING
In this example, the
start address is 17
and the dip switches
are set to a binary 3.
S1
SRU-8
1 1
9 9
5 5
2 2
10 10
6 6
3 3
11 11
7 7
4 4
12 12
8 8
To the control circuit
24 Vdc, 4A max.
rated for pilot duty
TB1 TB2
K1 K5
K2 K6
K3 K7
K4 K8
NC
NO
COM
Typical layout for a
single pole double
throw (SPDT) relay
terminal
Detail
Terminal Relay Description
TB1-1 K1 NC
TB1-2 K1 COM
TB1-3 K1 NO
TB1-4 K2 NC
TB1-5 K2 COM
TB1-6 K2 NO
TB1-7 K3 NC
TB1-8 K3 COM
TB1-9 K3 NO
TB1-10 K4 NC
TB1-11 K4 COM
TB1-12 K4 NO
Terminal Relay Description
TB2-1 K5 NC
TB2-2 K5 COM
TB2-3 K5 NO
TB2-4 K6 NC
TB2-5 K6 COM
TB2-6 K6 NO
TB2-7 K7 NC
TB2-8 K7 COM
TB2-9 K7 NO
TB2-10 K8 NC
TB2-11 K8 COM
TB2-12 K8 NO
SRU-8 Relay Table
Note: Power-limited if the source is power-limited. If the source is
nonpower-limited, maintain a space of 1/4 inch from power-limited wiring.
Otherwise, use FPL, FPLP, FPLR, or an equivalent in accordance with
the National Electric Code.
Make the ribbon cable connections. 2
JP1
P1 P1 P1
P1
P2 P2 P2
P2
2-SANCOM
From P1
on the
SAN-CPU
SRU-8 SWU-8(/3) SHO-4
A. Plug the ribbon cable assembly (P/N 250080) from P1 of the SAN-CPU into P2 of the 2-SANCOM.
B. Plug the ribbon cable from P1 of the 2-SANCOM to P2 of the next SAN series module.
C. Plug the ribbon cable from P1 of each SAN module to P2 of the next SAN module until you reach the last one.
D. Install the continuity jumper on the last SAN module.
Note: If the SIN-16 is
the last module,
install the continuity
jumper on JP1.
JP1
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com