manualshive.com logo in svg

EDM Solution 8, Руководство по установке, Страница: 36 / 54

Поделиться
Скачать
EDM Solution 8 Скачать руководство пользователя страница 36

Page 36

Solution-8 Installation Manual

ISSUE401.DOC

Electronics Design & Manufacturing

Dialler  Options 1

Location 218

0

When programming this location you will notice that there are four alternatives. You may select one, two, three
or all of these alternatives, however only one number needs to be entered. This number is calculated by adding
the option bit numbers together. Simply add the numbers together and the total is the number to be programmed.
Enter a seven (7) if you require options 1, 2 and 4 simultaneously  (ie. 1+2+4=7).

OPT

Function

1

Disable the dialler.

2

Enable smart lockout.

4

Allow horn speaker beeps for radio key operation.

8

Extend zone response time from 100ms to 400ms.

Disable the dialler

This option when set will disable all dialler operations but will still accept upload/download requests.

Enable smart lockout

This feature allows the control panel to remove any locked out zones from the lockout list only while the sirens
are running. This feature allows a monitoring station to receive codes from previously locked out zones during
siren time.

Allow horn speaker beeps for radio key operation

This feature will enable horn speaker beeps only to be heard when the system is armed via a radio key. Devices
connected to the Bell output will not be audible.

Extend zone response time from 100ms to 400ms

This option selects the zone response time for all eight input zones. A zone will have to be broken for the
prescribed time before alarming.

Dialler Options 2

Location 219

2

When programming this location you will notice that there are four alternatives. You may select one, two, three
or all of these alternatives, however only one number needs to be entered. This number is calculated by adding
the option bit numbers together.

Simply add the numbers together and the total is the number to be programmed. Enter a seven (7) if you require
options 1, 2 and 4 simultaneously.
(ie. 1+2+4=7).

OPT

Function

1

Enable radio key / key switch functions

2

Enable upload / download via a modem

4

Enable remote arming via the telephone

8

Send HI SPEED transmissions in single event mode.

Enable radio key /key switch module functions

This option must be selected when a Key switch Module is being used.

Содержание Solution 8























































Отзывы:

Нет отзывов