Eaton MGR10 Скачать руководство пользователя страница 74

Страница: 74 / 108

MGR10 A/B/C - Revision : I (for 7.0 software revision)

CALCulate:LIMit Group

These commands are used to set and query the lower and upper limit values used to test the measured
resistance. Exceeding these limits is reported in the Questionable Data Register (bits 11 & 12).

CALCulate:LIMit:LOWer <value>

Sets the lower measurement limit. The value is in Ohms (0 - 30,000).

CALCulate:LIMit:LOWer?

Returns the lower measurement limit in Ohms.

CALCulate:LIMit:UPPer <value>

Sets the upper measurement limit. The value is in Ohms (0 - 30,000).

CALCulate:LIMit:UPPer?

Returns the upper measurement limit in Ohms.

CALCulate:LIMit:STATe <ON|OFF> or <1|0>

Enables or disables the measurement limit facility.

CALCulate:LIMit:STATe?

Returns “0” (OFF) or “1” (ON).

CALCulate:LIMit:ALARm <ON|OFF> or <1|0>

Enables or disables the 'failed limit’ audible alarm.

CALCulate:LIMit:ALARm?

Returns “0” (OFF) or “1” (ON).

Содержание MGR10













































































































Результаты поиска

Содержание MGR10

Отзывы:

Похожие инструкции для MGR10

Бренды по названию

Популярные бренды

Eaton MGR10, Руководство по эксплуатации

Результаты поиска

Содержание MGR10

Отзывы:

Похожие инструкции для MGR10

Бренды по названию

Популярные бренды