manualshive.com logo in svg

Eaton MGR10, Руководство по эксплуатации

Поделиться
Скачать
Eaton MGR10 Скачать руководство пользователя страница 3

                               MGR10 A/B/C - Revision : I (for 7.0 software revision) 

 

 

 

3

 

 

 

Table of Contents 
 

SECTION 1.  INTRODUCTION .............................................................................................................................................. 5

 

1.1  OVERVIEW ................................................................................................................................................................... 6

 

1.2 Definitions and terminology ............................................................................................................................................ 8

 

1.3 Principles of measurement ............................................................................................................................................... 8

 

1.4  MGR10 and MGR10A technical specifications ............................................................................................................. 9

 

1.4.1  Measurement Accuracy

 ......................................................................................................................................... 9

 

1.4.2 Programmable current

 ........................................................................................................................................... 9

 

1.4.3  Accuracy against current level

 ............................................................................................................................. 9

 

1.5  MGR10B technical specifications ................................................................................................................................ 10

 

1.5.1  Measurement Accuracy

 ....................................................................................................................................... 10

 

1.5.2 Programmable current

 ......................................................................................................................................... 10

 

1.5.3  Accuracy against current level

 ........................................................................................................................... 10

 

1.6  MGR10C technical specifications ................................................................................................................................ 11

 

1.6.1  Measurement Accuracy

 ....................................................................................................................................... 11

 

1.6.2 Programmable current

 ......................................................................................................................................... 11

 

1.7  Common specification to all model numbers ............................................................................................................... 12

 

1.7.1 Temperature compensation

 ................................................................................................................................. 12

 

1.7.2 Lead resistance

 ...................................................................................................................................................... 12

 

1.7.3 Mains supply

 ......................................................................................................................................................... 12

 

1.7.7 Operating  conditions :

 ......................................................................................................................................... 13

 

1.7.8 Weight and Size :

 .................................................................................................................................................. 13

 

SECTION 2 : SETTING UP THE MGR10 ............................................................................................................................. 14

 

2.1  Safety information ........................................................................................................................................................ 14

 

2.2  Unpacking the instrument ............................................................................................................................................. 14

 

SECTION 3 : ABOUT THE MGR10 ...................................................................................................................................... 15

 

3.1  The Front Panel ............................................................................................................................................................. 15

 

3.2   ON/OFF Switch ........................................................................................................................................................... 15

 

3.3  The Function Keypad ................................................................................................................................................... 15

 

3.4  Summary of basic functions ......................................................................................................................................... 16

 

3.5  About the MGR10 Display screen ................................................................................................................................ 18

 

3.6 About the function keys ................................................................................................................................................. 19

 

SECTION 4 : SETTING UP MEASUREMENT PARAMETERS ......................................................................................... 21

 

4.1  Range Selection ............................................................................................................................................................ 21

 

4.2  Current Selection .......................................................................................................................................................... 22

 

4.3  Measurement Mode ...................................................................................................................................................... 23

 

4.4  Temperature Compensation .......................................................................................................................................... 28

 

4.5  Limits ............................................................................................................................................................................ 31

 

4.6  Data Logging Function ................................................................................................................................................. 33

 

4.7  General setup menu ...................................................................................................................................................... 36

 

4.8  Measure/Hold function ................................................................................................................................................. 40

 

4.9  Measure Stop Function ................................................................................................................................................. 41

 

4.10  ZERO Function ........................................................................................................................................................... 41

 

SECTION 5 : MEASURING WITH THE MGR10 ................................................................................................................. 42

 

5.1  Connecting to the MGR10 ............................................................................................................................................ 42

 

5.2  Connecting to the resistance ......................................................................................................................................... 43

 

5.3  Resistance measurement ............................................................................................................................................... 44

 

5.4  Resistance measurement with temperature compensation ............................................................................................ 44

 

5.5  Measurement with Limits ............................................................................................................................................. 45

 

SECTION 6 :REMOTE CONTROL INTERFACE ................................................................................................................ 47

 

6-1 PLC remote control ( option MGR10-02) ..................................................................................................................... 47

 

6-1-1 Unit setup :

 ............................................................................................................................................................ 47

 

6-1- 2 Contact specifications :

 ....................................................................................................................................... 47

 

6-1-3 Logical states definition :

 ..................................................................................................................................... 48

 

6-1- 4 Connection :

 ......................................................................................................................................................... 48

 

Содержание MGR10













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды