manualshive.com logo in svg

Eaton MGR10, Руководство по эксплуатации

Поделиться
Скачать
Eaton MGR10 Скачать руководство пользователя страница 71

                               MGR10 A/B/C - Revision : I (for 7.0 software revision) 

 

 

 

71

 

 

 

needed for each measurement. If CONTinuous triggering is “on”, then repeated FETCh? 
commands can be made to return the most recent measurement. 
 
One of three optional functions can be included with this command: 
FRESistance -  

Returns the uncompensated resistance and is the default for the first FETCh? 

 
TEMPerature -  

Returns the temperature value of the external Pt100 probe, providing that 
temperature compensation is “ON” and set to “EXT” mode. Otherwise, an 
“execution error” is generated and the error value is returned. 

 

TCOMpensate - 

Returns the compensated resistance value at 20°C, providing that temperature 
compensation is “ON”. Otherwise, an “execution error” is generated and the 
error value is returned. 

 
If no function is subsequently entered, then the function used in the previous FETCh? or READ? 

command is used. 

 

INITiate:CONTinuous <ON|OFF> or <1|0> 

Setting  to OFF means that any subsequent READ?, or INIT followed by FETCh?, will take one 
reading and send it to the output buffer. 
 
If set to ON, the microhmmeter will perform continuous measurements, which will be initiated 
immediately, and FETCh? will send the most recent value to the output buffer. The  measurements 
can be stopped by setting CONTinuous to OFF. 
 

(For the MGR10A  model operating on battery power, continuous mode is not available, and 
INITiate:CONTinuous ON will cause an “execution error” to be generated).  

 

INITiate:CONTinuous? 

Returns “0” (OFF) or “1” (ON). 

 

READ[ FRESistance|TEMPerature|TCOMpensate]? 

Triggers and returns a measurement. It is identical to INITiate, followed by FETCh?. See the 
FETCh? command above, for use of additional functions.  
 

This command is not available when the CONTinuous triggering mode is “on”, nor when 
DATAlogging mode is “on”, in which cases, an “execution error” will be generated and the error 
value returned. 

 
ABORt 

Stops the current measurement and clears the input and output buffers. 

ABORt works for RS-232 only. If sent in IEEE-488 mode, it will generate a “command error”. 

Содержание MGR10













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды