Capitole 40
1991.901 G01 002 35
With epoxy resin insulated busbars
Tee-off takes place as described on the previous page for
the respective busbar system with air-insulated busbars.
A
TTENTION
Bare busbar must be visible both to the left and
the right of the coupling.
Check whether the plastic caps are fittedover the nuts
under the tee-off strips, see Figure 2-51
Fit the screening cap, see Figure 2-52. For single busbar
and for parallel busbars the same cap is used. In the case
of single busbar/phase the dummy-bar must be used, see
Figure 2-47.
Figure 2-51: Uncovered copper on both sides clearly
observable (5 mm)
Figure 2-52: Mounting protection cover
2.2.2.8
Closing off the busbar compartment
If there is no auxiliary busbar system located in the
main busbar compartment
We have now reached the stage when the busbar cover
can be fitted. To begin with, the busbar cover on the front-
side is sealed. For each cubicle the busbar cover is
attached using two or three clinder head screws M5.
Channel parts should be placed in the recesses where the
compartments meet and at the ends of the cubicles. The
channel-parts have been fitted with a self-adhesive sealing-
strip, see Figure 2-53.
The top plates are then fitted. These are attached using
thread roll bolts (self-tapping) M5x10. In order to insure
proper sealing of the busbar cover, four bolts M10x16 are
suplied with each cubicle. These bolts have to be fitted in
the holes for the lifting-eyes in the corners of the cubicle.
If there is an auxiliary busbar systemon the panel
front side in a separate compartment
See above, and then: Hook the connector to the
premounted columns. Check that the end-covers have
been fitted. Fit the cover using two or three cylinder head
screws M5.
Figure 2-53: Channel part in busbar compartment
protection
caps
Содержание Holec Capitole 40
