background image

EFX48-xx Series with RM3-340/440 Installation and Operation Guide 

 

56 

Copyright © 2019 Eaton Corporation.  All Rights Reserved. 

IPN  March 2019 

 

 

  

 

Installation Tasks 

Before starting the installation, review the following information: 

 

Required Equipment and Tools on page 153 

 

Warnings and Cautions on page 52 

 

Inspecting the Equipment and Reporting Damage on page 53 

 
Complete the Installation tasks in the following order: 

 

Task  Description 

Reference 

Check the AC Supply and Grounding 

See details on page 56 

Move Mounting Brackets (if required) 

See details on page 58 

Mount the RM3-340/440 in the Rack 

See details on page 59 

Connect the DC Load and Battery Cables 

See details on page 61 

Install the Batteries 

See details on page 64 

Connect Mid-point Monitoring (if required) 

See details on page 64 

Mount the Battery Temperature Sensor 

See details on page 65 

Connect External Input/Output Cabling (if required) 

See details on page 66 

Connect to the AC Supply Point 

See details on page 67 

 
 

 

Task 1 - Check the AC Supply and Grounding 

It is important that the ac supply for the RM3-340/440 dc power system includes the correct 

levels of protection. 

Step 1 - High ac voltage protection at the site 

 

 

Check if the ac voltage is expected to exceed 275V (L-N or L1-L2). 

If so, then it is strongly recommended that an external high voltage protection 

unit (HVPU) be installed. This will automatically disconnect the ac at high 

voltage and reconnect it at normal voltage. 

Install the HVPU as in the following diagram. 

Connect the High VAC alarm output to one of the Digital Inputs on the GPIO 

terminal block of the EFX48 e-Fuse unit (see the diagram on page 151 for 

location). Then configure this Digital Input as the High VAC alarm by following 

the instructions on page 102.  

 

The High VAC alarm signal lines must be isolated from the ac supply by a 

voltage-free relay contact – note that this is NOT contained within the 

EFX48 unit. 

 

Содержание EFX48 e-Fuse Series


































































































































































Отзывы: