Eaton EFX48 e-Fuse Series Скачать руководство пользователя страница 67

Страница: 67 / 161

Installation

IPN March 2019



GPIO terminal #14



GPIO terminal #1

Step 2 - Terminate the cabling



•

Connect only voltage-free switch or relay contacts to Digital Inputs.

•

Do not exceed the voltage and current limits of the relay contacts.

•

For wire size and I/O ratings see Specifications on page 138.

Terminate the cable as in the diagram above.

Use cable ties to secure the cable and prevent strain on the connectors.

Step 3 - Set up EFX48

Configure the inputs and outputs after completing the installation and all the Startup

Tasks on page 69 Operation information on page 75.

Procedure complete

Task 9 - Connect to the AC Supply Point

Step 1 - RM3-340/440 systems with IEC cord sets

If the RM3-340/440 has permanently connected ac cords then go to Step 2.

Connect one of the cord sets provided to each IEC connector on the rear of the RM3-

340/440.



If the cord sets are missing or must be replaced then refer to Spare Parts on

page 154 for replacement items.





Содержание EFX48 e-Fuse Series



























































































































































Результаты поиска

Содержание EFX48 e-Fuse Series

Отзывы:

Похожие инструкции для EFX48 e-Fuse Series

Бренды по названию

Популярные бренды

Eaton EFX48 e-Fuse Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EFX48 e-Fuse Series

Отзывы:

Похожие инструкции для EFX48 e-Fuse Series

Бренды по названию

Популярные бренды