Eaton EFX48 e-Fuse Series Скачать руководство пользователя страница 58

Страница: 58 / 161

EFX48-xx Series with RM3-340/440 Installation and Operation Guide

IPN March 2019

Time-Current Curve (minimum and

maximum)



APR48-ES internal fuses (IEC 60127-2)

Sources:

Schurter SP 5x20 Pigtail data sheet.

Step 5 - Check the grounding arrangements at the site

Confirm that all grounds are brought together at one "star" point so that surge

currents cannot flow in "ground loops" and create large voltages.

Procedure complete

Task 2 - Move Mounting Brackets (if required)

RM3-340/440s are pre-assembled with 19-inch rack-mounting brackets as shown in the diagram

on page 59.
If required, the brackets can be moved to an alternate position or replaced with brackets for use

in 23-inch wide racks.

Step 1 - Remove brackets

Remove top cover.

Undo the screws holding each bracket.

Remove the brackets and internal plates.

Step 2 - Fit 23-inch mounting brackets (if required)

Содержание EFX48 e-Fuse Series



























































































































































Результаты поиска

Содержание EFX48 e-Fuse Series

Отзывы:

Похожие инструкции для EFX48 e-Fuse Series

Бренды по названию

Популярные бренды

Eaton EFX48 e-Fuse Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EFX48 e-Fuse Series

Отзывы:

Похожие инструкции для EFX48 e-Fuse Series

Бренды по названию

Популярные бренды