background image

19

7   Common operation of the web screens

Installation and Operating Instructions  Web-Controller

   40071860236 (E)   February 2019   www.eaton.com

In the menu “Commands” 

1

 all commands can be 

sent to single 

luminaires. It is possible to 

send the commands to all 

luminaires or to one line, 

zone or even to a single 

luminaire.

2

Status display of the total 

system and the pot.-free 

IN/OUT puts.

The following commands 

3

 can be set:

O

O

Block:

 Emergency light function and maintained mode 

are deactivated, e.g. during idle operating times

O

O

Rest mode:

 During a mains failure (luminaires are in 

emergency mode), the rest mode will switch OFF the 

luminaires. If mains return, the luminaires will go back 

in normal mode. To the next mains failure, the lumi-

naires switch again to emergency mode.

O

O

Release / Relight: 

Release of the blocking or rest 

mode function

O

O

Start functional test

: Specified luminaires start a func-

tion test

O

O

Start duration test:

 Specified luminaires start a battery 

duration test

O

O

Stop FT / DT:

 Function tests or duration tests are 

aborted

O

O

Switch maintained mode ON / OFF:

 Luminaires in 

maintained mode (L’ applied) can be switched ON or 

OFF (if luminaire supports this function)

O

O

Update luminaire status:

 Actualisiation of the lumi-

naire status of all luminaires

O

O

Update luminaire type:

 Actualisation of luminaire type 

information

7.8   Switching command screen

1

2

3

4

O

O

Search all lamp:

 Completely new luminaire search 

– caution: old configurations are overwritten. All lumi-

naires will be addressed with a logical address from 1 

up to 200 or 1 up to 400.

O

O

Search new lamp:

 Starts a luminaire search and only 

adds newly found luminaires. All new luminaires will 

be addressed with a logical address from last existing 

luminaire up to 200 or up to 400.

O

O

Search initialized lamp:

 Already addressed luminaires 

keeps their addresses after search

O

O

Load config PC soft:

 Load a configuration which was 

created by the PC software. The config file 

must have the filename „config.xml

Selection of luminaires to be controlled 

4

:

O

O

Line:

 Selection of luminaire lines 1 to 4

O

O

Zone:

 Selection of luminaire zone 2 to 16

O

O

Luminaire:

 Selection of single luminaires in the line 

and zone

O

O

If “All” is selected:

 Command applies to all lumi-

naires 

Содержание CGLine+ Web Controller





























Отзывы: