Eaton C441 Series Скачать руководство пользователя страница 30

Страница: 30 / 76

Configuration Using the PROFIBUS Configuration File

C441 PROFIBUS Module User Manual

MN042002EN—July 2015

www.eaton.com

Motor Phase Loss Trip Level

S811+

1–100%

Motor Phase Loss Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Motor Phase Imbalance Fault Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Motor Phase Imbalance Fault Level

S811+

1–100%

Motor Phase Imbalance Fault Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Motor Voltage Imbalance Fault Level

S811+

1–100%

Motor Voltage Imbalance Fault Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Motor Under Voltage Fault Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Motor Under Voltage Fault (% of Rated Voltage)

S811+

1–99%

Motor Under Voltage Fault Duration (Running)

S811+

0.1–60.0 sec (in 0.1 sec)

Motor Over Voltage Fault Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Motor Over Voltage Fault (% of Rated Voltage)

S811+

101–120%

Motor Over Voltage Fault Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Motor Line Frequency Fault (Warning) Enable, Len=1

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Motor Line Frequency Deviation From Rated Fault
Level

S811+

0–100% deviation from setting

Motor Line Frequency Fault Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Motor Average Power Fault (Warning) Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Motor Average Power Percent Rated Low Fault Level S811+

0.0–100.0% (in 0.1%)

Motor Average Power Percent Rated High Fault Level S811+

0.0–800.0% (in 0.1%)

Motor Average Power Fault Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Analog Input Fault (Warning) Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Analog Input Percent of Rated Range Low Fault Level S811+

0–100% (of range)

Analog Input Percent of Rated Range High Fault Level S811+

0–100% (of range)

Analog Input Fault Duration

S811+

0.1–60.0 sec (in 0.1 sec)

Temperature Sensor Fault Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

SCR Not Firing Fault Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

SCR Shorted Fault Enable

S811+

0 = Protection disabled
1 = Fault enabled
2 = Warning enabled

Alarm No Trip Enable

S811+

1 = enable
0 = disable

Table 20. S811+ Soft Starter Configuration File, continued

Parameter Name

Location

Notes

Содержание C441 Series













































































Результаты поиска

Содержание C441 Series

Отзывы:

Похожие инструкции для C441 Series

Бренды по названию

Популярные бренды

Eaton C441 Series, Руководство пользователя

Результаты поиска

Содержание C441 Series

Отзывы:

Похожие инструкции для C441 Series

Бренды по названию

Популярные бренды