DV Power RMO60TD Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 50

background image

17

RMO60TD Getting Started

The display shows the value of the test current in new tap position (here

9,82 A

), and the value of the

current ripple occurred during the change from previous position to the new one (here

4,7 %

). At the

moment the test current shown on the display is stable, the RMO60TD shows the resistance value in
new tap position (here

569,8

mΩ

). P

ress

Ω

to save the resistance and the ripple in the new position of

Tap Changer.

Repeat this procedure as often as needed until the results for RIPPLE and RESISTANCE are obtained
for all Tap Changer positions.
Test is completed pushing

STOP

.

When measurement is completed (after pressing

STOP

) RMO60TD switches to the

TapC

menu

and starts current discharging. During the current discharging process, the discharging LED lights
and alarms beep.

Discharge is completed when LED discharge and the buzzer are OFF. Also, during that period
“Discharging” message is shown on the display. During discharging process it is not possible to
start another measurement.

A properly working tap changer differs from malfunctioning one in a current discontinuity during the tap
change, by the magnitude of the current ripple value. A discontinuity will result in much higher current
ripple value (99 % or 100 %) than a properly functioning tap changer.

Note

:

Current ripple value depends on the construction of the tap changer. It is recommended to

compare current ripple values between each other got on one transformer. Also, it is recommended to
compare current ripple results on one transformer with results from some previous test in order to follow
conditions of that tap changer.

Figure 6-17 shows indication about possible tap changer bad conditions during the change from tap to
tap.

If current circuit is opened during the change from tap to tap, message „Discontinuity“ will be shown on
the display, red LED will light and buzzer will beep continuously. Discharging process starts.

Figure 6-16:
The

TapC

menu during

discharging

Figure 6-17:
The

TapC

menu

showing much higher
current ripple value

«
...
15
16
17
18
19
...
»

Содержание RMO60TD



















































Отзывы:

Нет отзывов

Похожие инструкции для RMO60TD

Бренд: JGR Страницы: 12

Бренд: R&S Страницы: 248

Бренд: Conrad Electronic Страницы: 38

Бренд: Seben Страницы: 16

Бренд: Maico Страницы: 2

Бренд: Ocean Reef Страницы: 24

Бренд: BANTE Страницы: 17

Бренд: E+E Elektronik Страницы: 4

Бренд: yellow jacket Страницы: 16

Бренд: KATA Страницы: 20

Бренд: Polhemus Страницы: 2

FTCI-3/4D15A4P-2LUX-H1141

Бренд: turck Страницы: 2

Бренд: BK Precision Страницы: 21

Temp70 PT100 vio

Бренд: XS Instruments Страницы: 19

Бренд: Kawai Страницы: 52

Бренд: Zenner Страницы: 12

DeltaOHM LPPYRA12

Бренд: GHM Страницы: 32

PCV100-F200-B17-V1D-6011

Бренд: Pepperl+Fuchs Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды