Repair service is available anytime.
• After the 90 day warranty, you can still have your Maximum
MT Pro repaired for a small charge by the experts at
DuraTrax’s authorized repair facility, Hobby Services, at the
address listed on the front page of this manual.
To speed up the repair process, please follow the
instructions listed below.
1. Under most circumstances return the
ENTIRE
system: truck
and radio. The exception would be sending in a Stress-Tech
part. See the instructions under Stress-Tech Guarantee.
2. Make sure the transmitter is turned off, all batteries are
removed and fuel is drained from the tank.
3. Send written instructions which include: a list of all items
returned, a
THOROUGH
explanation of the problem, the
service needed and your phone number during the day. If
you expect the repair to be covered under warranty, be
sure to include a proof of date of purchase (your store
receipt or purchase invoice).
4. Also be sure to include your full return address.
All pictures, descriptions and specifications found in this
instruction manual are subject to change without notice.
DuraTrax maintains no responsibility for inadvertent errors
in this manual.
Do not use too much force when tightening self-tapping
screws into plastic. Overtightening will cause the threads in
the plastic to strip. We recommend that you stop turning a
self-tapping screw when you feel some resistance as the
head of the screw comes in contact with the plastic. Avoid
using powered screwdrivers when assembling this kit. They
tend to overtighten the screws. Do not use thread locking
compound on any self-tapping screws. The thread locking
compound may damage the plastic.
IMPORTANT:
Use
thread lock on any fastener that is threaded into metal or
fastened with a nut. Vibration from the engine will cause the
screws to loosen if thread locking compound is not used.
To operate the Maximum MT Pro these items are required:
• Fuel (DuraTrax Red Alert fuel - DTXP0520)
• Air Filter Oil (DTXC2465)
• Glow plug wrench (DTXR1170)
• Hobby knife (HCAR0105), #11 blades (HCAR0211)
• It is also helpful to have a couple of extra glow plugs on
hand (O.S. #A3 plug - OSMG2690)
• R/C Body Reamer (DTXR1155)
The DuraTrax Nitro Starter Pack (DTXP0200) contains
fuel, fuel bottle, glow plug starter, glow plug wrench
and glow plug.
For the Pre-Built version of the Maximum MT Pro, you will
also need:
• 2-channel radio with two (2) standard servos (FUTJ20**)
• Twelve (12) “AA” batteries - Four (4) for the receiver and
eight (8) for the transmitter
• Small bottle of thread locking compound (GPMR6060)
• Glow plug starter (DuraTrax Rapid Heat - DTXP3000)
• Fuel bottle (DuraTrax Kwik-Pit Bottle - DTXP0125)
To assemble the Pre-built version (DTXC0075), you will
need the following tools:
• Phillips head screwdriver (DTXR0124)
• Flat blade screwdriver (DTXR0158)
• Needle-nose pliers (DTXR0300)
• Wire cutters or diagonal cutters (HCAR0630)
• Hobby knife (HCAR0105), #11 blades (HCAR0211)
• Drill with 1/4", 1/8", 5/64" (or 6mm, 3mm, 2mm) bits
• R/C Body Reamer (DTXR1155)
TOOLS YOU WILL NEED
REQUIRED ITEMS FOR COMPLETION
3mm
14mm
M3x14 Screw
3mm
14mm
M3x14
Self-Tapping
Screw
SCREW INFORMATION
SPECIFICATION & DESCRIPTION CHANGES
REPAIR SERVICE
3
