Duratrax Maximum MT Pro Скачать руководство пользователя страница 20

ACCESSORIES AND OPTIONAL PARTS

Transmitter Nicd Conversion Kit

Save by powering your transmitter with
rechargeable NiCds! This kit includes eight "AA"
Sanyo

®

NiCd cells and a 110V AC wall charger.

Connect it to the radio's charge jack, and you can
recharge the batteries in just 2-3 hours — without
removing them from the transmitter.  

DTXP4010

DuraTrax Ultimate Car Wrench

This chromed, cast metal wrench has threaded holes
for storing up to 4 glow plugs; a combination
slotted/phillips screwdriver bit; and seven socket
head sizes. Bits fit into a 6mm hex shank inside both
the long 8mm socket (for easy access) and the
12mm socket (for more torque).  

DTXR1175

DuraTrax Red Alert™ 20% Racing Fuel

To make your TORQ™ 21 engine run faster,
better and longer, you need the unique
formula of DuraTrax Red Alert. Red Alert
contains 20% nitro plus a carefully race-tested
blend of castor and synthetic oils. 

DTXP0600

DuraTrax Nitro Starter Set

This set includes everything you need to start
racing. 5-way glow plug wrench, 1 qt. of Red
Alert fuel, Rapid Heat

®

glow starter w/charger,

fuel bottle and glow plug. 

DTXP0200

DuraTrax Crankshaft Locking Tool

Remove your engine’s clutch safely with this
easy to use, anodized metal tool. Works with
all .10 to .21 car and truck engines.

DTXR1100

DuraTrax XL Deluxe Field Bag

Keep your gear loaded and race ready with
the XL Deluxe Field Bag. Heavy duty black
nylon bag with red trim and white logo.

DTXP2010

Pit Tech Deluxe Car Stand

The sturdy stand disassembles easily and stores
flat. The plate rotates for all-sides access, and
built-in holes keep shocks handy when rebuilding.
Molded rubber inserts grip chassis securely, and
the dropped center accommodates models with
uneven chassis bottoms.

DTXC2370

Engine Tuning Screwdriver

Now you don't need separate drivers for adjusting
high- and low-speed needles and throttle stop
screws — just this one! The hardened chrome
vanadium steel shaft is 120mm long and plenty
tough, and the 3.2mm wide tip is magnetized for
added convenience.

DTXR0185

Rapid Heat Glow Starter w/ Charger

Rapid Heat's 1500mAh Sanyo

®

NiCd sends

power to a 1-3/4" socket with the distinctive
Twist-and-Lock tip.Made of durable metal, with a
vinyl cap to protect the tip from fouling. A 110V
AC charger is included for overnight recharging.

DTXP0150

Содержание Maximum MT Pro





















Отзывы: