Duplo DF-755 Скачать руководство пользователя

Страница: 55 / 86

3-21

Chapter 3 ADVANCED OPERATION

Rough

adjustment knob

Move the rough adjustment knob of

the second folding plate to the upper

end.

●

The rough adjustment knob cannot

be turned either clockwise or coun-

terclockwise. Make sure that you pull

up the knob when you want to move

it. ( p.2-4)

●

After moving the rough adjustment

knob, turn the fine adjustment knob

to the right and left a few times to

check that it moves slightly. ( p.2-5)

Stacker roller

Move the stacker rollers to the ap-

propriate position.

The machine shown in the figure to the

right is a North America model.
Refer to the table of stacker rollers position

attached to the control panel section (for

EU) or to the paper receiving tray (for North

America) for their appropriate position (

p.3-13).
For this example (A4/LT size, single fold),

move the stacker rollers to "3."

Top cover

Open the top cover.

Set screw

Paper feed ring

Loosen the set screw of the paper

feed ring.

Move the paper feed ring at the far

end to the folded line of the paper.

Tighten the set screw of the paper

feed ring.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды