Duplo DF-755 Скачать руководство пользователя

Страница: 31 / 86

2-5

Chapter 2 BASIC OPERATION

Fine adjustment knob

First folding plate

Second folding plate

2) Turn the fine adjustment knob to the

right and left a few times and check that

it moves slightly.

For EU

When stacking A4 and B5 size paper with

long edge feed, move the rough adjustment

knob to the mark of “A5” and “B6” respec-

tively.

Use the mark on the folding plate just as

a reference. You may need fine adjust-

ments according to various conditions

such as environmental conditions (tem-

perature, humidity), paper quality, paper

thickness, paper fiber direction, cutting

accuracy and printing conditions.

Paper feed pressure

adjustment knob

Set the paper feed pressure adjust-

ment knob to “Thin paper.”

If the paper slips and no paper is conveyed,

change the paper feed pressure from “Thin

paper” to “Thick paper”.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды