Duplo DF-755 Скачать руководство пользователя

Страница: 44 / 86

3-10

Chapter 3 ADVANCED OPERATION

Press the Start button to start folding

operations.

Press the Stop button to interrupt or stop

the operations. Pressing the Start button

again will resume operations.
When there is no paper on the paper feed

table, the machine will stop automatically

and the counted number and "NO PAPER"

will be displayed alternately.
When paper is loaded on the paper feed

table, only the counted number will be dis-

played. If you press the C button for more

than two seconds, the counter returns to

"0." If you press the Start button without

pressing the C button, folding operations

will resume and the accumulated number

will be displayed on the counter.

Note that you cannot move onto the next

procedure until you place paper on the

paper feed table.

After completing the work, remove

the guide plate unit.

● Leaving the guide plate unit attached

may result in problems when other

types of paper are used.

● When folding fine quality paper 52.3

g/m

/14 lb into four, do not use the

guide plate unit.

Store the removed guide plate unit

inside the top cover.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды