manualshive.com logo in svg

Duplo DF-755, Инструкция по эксплуатации

Поделиться
Скачать
Duplo DF-755 Скачать руководство пользователя страница 39

3-5

Chapter 3 ADVANCED OPERATION

Stacker roller

5 

Move the stacker rollers to "5."

The machine shown in the figure to the 

right is a North America model.

Stacker roller

Lever

Belt

Stacker lever

6 

While lifting up the stacker rollers 

with your hand, pull the levers (left 

and right) attached to the stacker 

lever in the direction of the arrow so 

that the stacker rollers are lifted up.

7 

Press the Start button for test fold-

ing and check if the paper is ejected 

smoothly.

8 

Press the Stop button after a couple 

of folded sheets are ejected.

Stacker roller

9 

If the paper is not ejected smoothly, 

change the position of the stacker 

rollers to "3" or "4."

The machine shown in the figure to the 

right is a North America model.

Folded sample

10

  Check the finish of test folding.

Check for folding misalignment using the 

second test folded sample.
If folding misalignments occur, refer to 

Chapter 3 "ADVANCED OPERATION"“5.

Correcting Folding Misalignment” 

( p.3-27).

Содержание DF-755























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды