manualshive.com logo in svg

Duplo DF-755, Инструкция по эксплуатации

Поделиться
Скачать
Duplo DF-755 Скачать руководство пользователя страница 33

2-7

Chapter 2 BASIC OPERATION

Test folded sample

11

  Check the finish of test folding.

Check for folding misalignment using the 

second test folded sample.
If folding misalignments occur, refer to 

Chapter 3 "ADVANCED OPERATION"“5.

Correcting Folding Misalignment” 

( p.3-27).

Clear button

12

  After completing adjustments, press 

the C (clear) button for more than 

two seconds to clear the counter to 

"0."

13

  Press the Start button to start folding 

operations.

Press the Stop button to interrupt or stop 

the operations. Pressing the Start button 

again will resume operations.
When there is no paper on the paper feed 

table, the machine will stop automatically 

and the counted number and "NO PAPER" 

will be displayed alternately.
When paper is loaded on the paper feed 

table, only the counted number will be dis-

played. If you press the C button for more 

than two seconds, the counter returns to 

"0." If you press the Start button without 

pressing the C button, folding operations 

will resume and the accumulated number 

will be displayed on the counter.

Note that you cannot move onto the next 

procedure until you place paper on the 

paper feed table.

Содержание DF-755























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды