background image

3-19

Chapter 3 ADVANCED OPERATION

4.  Cross Folding

Cross folding is to fold single-folded paper another time into two or three.

Cross fold

Cross single fold

Cross letter fold

  The maximum paper thickness is 104.7 g/m²/28 lb. However, this thickness may differ 

slightly according to various conditions such as environmental conditions (tempera-

ture, humidity), paper size, and paper fiber direction.

●  When the paper is cross folded, Σ folding (folding slippage in the horizontal) and fold-

ing misalignment along sides of paper may occur due to conditions such as environ-

mental conditions (temperature, humidity), paper size and paper fiber direction. This is 

not a malfunction of the machine.

 folding

4-1.  Cross Folding Standard Size Paper

The paper size that can be cross folded is A3, B4, A4 and B5/LD, LG, LT.
The following describes the cross single folding procedures of A3/LD size paper.

Only short edge feed is available for 

cross folding.

Fold A3/LD size paper into two ac-

cording to Chapter 2 "BASIC OPERA-

TION" "1.Standard Folding of Stan-

dard Paper" ( p.2-2).

Press along the folded line of the 

single-folded paper firmly with your 

fingers to prevent the paper from 

slipping and buckling in the horizon-

tal direction when folded.

Содержание DF-755























































































Отзывы: