manualshive.com logo in svg

Duplo DF-755, Инструкция по эксплуатации

Поделиться
Скачать
Duplo DF-755 Скачать руководство пользователя страница 78

5-2

Chapter 5 CLEANING THE UNIT

1.  Cleaning Each Section

The adherence of paper dust and printing ink on the rubber rolls and paper feed rings may cause 

problems such as paper feed errors and folding misalignment. Adherence of paper dust near sensors 

will also cause misdetection. Clean the machine once a week. We recommend that you use a com-

mercially-available air duster for office equipment to clean sensors.

●

  Prior to cleaning, be sure to disconnect the power cord from the outlet.

●  After cleaning, make sure that the areas that were cleaned are completely dry before 

resuming paper folding operations.

 

Do not use flammable sprays or solvent inside or near the unit (e.g.
when cleaning the unit).

Such flammable gas may ignite and cause a fire or combustion.
Take precautions against fire and ensure ventilation when using alcohol, and store the
alcohol in a safe place after use. Also note that use of other solvents can damage the
rubber rollers and resin inside the unit, resulting in malfunctions.

1-1.  Cleaning the Rubber Roll

Top cover

1 

Open the top cover.

Second folding plate

First folding plate

2 

Remove the first folding plate 

and second folding plate from the 

machine.

Содержание DF-755























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды