Duplo DF-755 Скачать руководство пользователя страница 54

Страница: 54 / 86

3-20

Chapter 3 ADVANCED OPERATION

Paper

Side guide

Paper set lever

36 mm/

1-1/2 inches

Raise the paper set lever and stack

the single-folded paper on the paper

feed table with the folded line facing

the non-operator's side.

The amount of paper stacked on the pa-

per feed table should be approximately

2/3 (approx. 36 mm/1-1/2 inches) of the

height of the side guide.

Loosen the fixing screws of the side

guides.

Side guide

Fixing screw

After pressing the side guide to each

side of the paper lightly, tighten the

screws to secure the side guides.

Paper set lever

Lower the paper set lever.

The paper feed table will be raised.

Make sure that you lower the paper set

lever. If you start operations without the

paper set lever lowered, the paper feed

rings will run idle, causing the machine

to stop.

Rough adjustment knob

Move the rough adjustment knob of

the first folding plate to the position

for single-fold A4/LT paper.

For EU

If the original paper size is B4, A4 or B5,

the knob should be moved to the position of

B5, A5 or B6 respectively.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Бренды по названию

Популярные бренды