Duplo DF-755 Скачать руководство пользователя

Страница: 30 / 86

2-4

Chapter 2 BASIC OPERATION

Side guide

Fixing screw

After pressing the side guide to each

side of the paper lightly, tighten the

screws to secure the side guides.

Paper can be stacked to a height of ap-

proximately 45 mm/1.77 inches at one

time. Do not stack too many sheets of

paper.

Paper set lever

Lower the paper set lever.

The paper feed table will be raised.

Make sure that you lower the paper set

lever. If you start operations without the

paper set lever lowered, the paper feed

rings will run idle, causing the machine

to stop.

Rough adjustment knob

First folding plate

Second folding plate

Rough adjustment knob

Move the rough adjustment knob of

the first and second folding plates to

the mark of a folding pattern you de-

sire.

Because the second folding plate is not

used for a single fold, move the rough

adjustment knob of the second folding plate

to the upper end to prevent the paper from

being sent to the second folding plate.

"Folding paper into two" ( p.2-8)

Rough adjustment knob

1) Slide the rough adjustment knob while

pulling it up.

The rough adjustment knob cannot

be turned either clockwise or

counterclockwise. Make sure that you

pull up the knob when you want to move

it.

Содержание DF-755























































































Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды

Duplo DF-755, Инструкция по эксплуатации

Результаты поиска

Содержание DF-755

Отзывы:

Похожие инструкции для DF-755

Бренды по названию

Популярные бренды