manualshive.com logo in svg

Duke 957R, Руководство оператора, Страница: 42 / 56

Поделиться
Скачать
Duke 957R Скачать руководство пользователя страница 42

34

184662

DUKE  Model 957R Soft Serve Freezer

Poor or slow
product
recovery.

1.

Dirty or blocked condenser, restricted
air flow - high ambient temperature.

1.

Lower ambient temperature; Contact
your local authorized service
company.

2.

Thermostat cut in point out of
adjustment or malfunctioning.

2.

Contact your local authorized service
company.

3

Component or compressor failure.

3.

Contact your local authorized service
company

Beater motor
does not
operate.

1.

Head assembly is not installed.

1.

Install head assembly.

2.

Magnetic head switch defective.

2.

Contact your local authorized service
company.

3.

Component failure.

3.

Contact your local authorized service
company.

Compressor
and beater
motor operate
only when
dispensing.

1. Cylinder thermostat, setting too warm,

or thermostat defective.

1. Contact your local authorized service

company.

Compressor
and beater
motor do not
operate when
dispensing.

1. Spigot switch(es) defective or out of

adjustment.

1

Contact your local authorized service
company.

2. Time delay defective.

2. Contact your local authorized service

company.

Troubleshooting Table   - 

    

continued

PROBLEM

PROBABLE CAUSE

REMEDY

Содержание 957R

























































Отзывы:

Нет отзывов