DSE DSE7560 Скачать руководство пользователя страница 59

Страница: 59 / 62

DSE Model 7560MK1 Main Control and ATS Operators Manual

057-015 7560MK1 OPERATING MANUAL ISSUE 10 10/02/09 AM

NEMA CLASSIFICATIONS

NOTE: - There is no direct equivalence between IP / NEMA ratings. IP figures shown are

approximate only.

IP30

Provides a degree of protection against contact with the enclosure equipment and against a limited amount of
falling dirt.

IP31

Provides a degree of protection against limited amounts of falling water and dirt.

IP64

Provides a degree of protection against windblown dust, rain and sleet; undamaged by the formation of ice on the
enclosure.

IP32

Provides a degree of protection against rain and sleet:; undamaged by the formation of ice on the enclosure.

4 (X)

IP66

Provides a degree of protection against splashing water, windblown dust and rain, hose directed water;
undamaged by the formation of ice on the enclosure. (Resist corrosion).

12/12K

IP65

Provides a degree of protection against dust, falling dirt and dripping non corrosive liquids.

IP65

Provides a degree of protection against dust and spraying of water, oil and non corrosive coolants.

Содержание DSE7560































































Результаты поиска

Содержание DSE7560

Отзывы:

Бренды по названию

Популярные бренды

DSE DSE7560, Руководство пользователя

Результаты поиска

Содержание DSE7560

Отзывы:

Бренды по названию

Популярные бренды