DSE DSE7560 Скачать руководство пользователя страница 49

Страница: 49 / 62

DSE Model 7560 ATS and Mains Controller Operators Manual

057-017 7560 OPERATING MANUAL ISSUE 10.2 10/02/09 AM 49

7.6 RUNNING EDITOR

7.6.1 ACCESSING THE ‘RUNNING’ CONFIGURATION EDITOR

•

The ‘running’ editor can be entered while the engine is running. All protections remain active if the engine is running while
the running editor is entered.

•

Press and hold the

button to enter the running editor.

EDITING A PARAMETER

•

Enter the editor as described above.

•

Press the left

or right

buttons to cycle to the section you wish to view/change.

•

Press the up

or down

buttons to change the parameter to the required value.

•

To save paremeters scroll to `save changes and exit followed by the down

buttton

•

To cancel changes scroll to `Abandon changes and exit followed by the down

button

ADJUSTABLE PARAMETERS (Running editor)

Running Editor

Section

Parameter as shown on display

Factory Settings

DISPLAY Contrast

Language

English

Load power factor

Load parallel power

Enable commissioning screens

Voltage adjust

(manual mode only engine running bus breaker open)

Raise Steady Lower

Frequency adjust

(manual mode only engine running bus breaker open)

Raise Steady Lower

Enable mains decoupling

Abandon changes and exit

Save changes and exit

Содержание DSE7560































































Результаты поиска

Содержание DSE7560

Отзывы:

Бренды по названию

Популярные бренды

DSE DSE7560, Руководство пользователя

Результаты поиска

Содержание DSE7560

Отзывы:

Бренды по названию

Популярные бренды