DSE DSE7560 Скачать руководство пользователя страница 32

Страница: 32 / 62

DSE Model 7560 ATS and Mains Controller Operators Manual

32 057-017 7560 OPERATING MANUAL ISSUE 10.2 10/02/09 AM

The system will remain in this mode until further action is taken.

Pressing the transfer to mains/open bus button

once will synchronise the bus to the mains.

The 7560 will display:

Status

Synchronise bus

Manual mode

Once the bus has synchronised to the mains, the
mains will close and power will be ramped off the
bus (generators). The 7560 will display:

Status

Ramp off bus
10% kW 12% kVAr
Manual mode

Once the bus power / mains power level has been
reached (configured using 75xx software) the
7560 will display:

Status

Continuous paralleling

Manual Mode

The system will remain in this mode until further action is taken.

Operation

Detail

Pressing the transfer to mains/open bus button

again will transfer the remaining load onto the

mains. The 7560 will display:

Status

Ramp off bus
10% kW 12% kVAr
Manual mode

Once the bus loading has reached 0kW the bus
will open and the 7560 will display:

Status

Mains on load

Manual mode

Pressing the red stop button will issue a stop to all
7510s on the system

The LED above the button will illuminate and the
LCD display will briefly indicate:

Status

Mains on load

Stop mode

Any 7510 running in auto mode will then display:
Please refer to the 7510 operating manual for
further details of the 7510 stop sequence

RETURN DELAY

00:50

NOTE:- Pressing the STOP/RESET button

at any time will transfer the load to the

mains and stop the generators.

Содержание DSE7560































































Результаты поиска

Содержание DSE7560

Отзывы:

Бренды по названию

Популярные бренды

DSE DSE7560, Руководство пользователя

Результаты поиска

Содержание DSE7560

Отзывы:

Бренды по названию

Популярные бренды