background image

3G4010 Wiring Diagrams

15

 Figure 5 - Fire Alarm Control Unit and 3G Transmitter

Wiring Diagram for Fire Alarm Control Unit (with dialler) and 3G (HSPA/2G (GPRS) Transmitter (Passive Communication System)

 

 

 

 

 

 

 

 

 

 

 

         

  AUX Power 
(12V/700mA) 

RM1C ULC 
Relay 

Fire Alarm 

Control Unit 

TIP/RING 

Zone Input        

          

Outputs 

Fire

Trouble  

3G Wireless
Transmitter 

 

3G4010

T1/R1 

                

TIP/RING

Zone 

     

PGM4

Inputs        Output  

3G4010 cabinet 

3G (HSPA) or
2G (GPRS)

AC Input 

NOTES:

- Power for 3G4010 shall be provided from Fire 

Alarm Control Unit or separately Listed power supply 
rated for the application, 12V/700mA (Jumper CON5
shall be set to on for Fire Monitoring). 

- All wiring connections must be run in a protective   

conduit. 

- For local supervision of the wireless transmitter connect 

PGM output from 3G4010 to one zone input on the 
Fire Alarm Control Unit. 

- Dry Contact Trouble output from ULC Listed Fire 

Alarm Control Unit must be connected to zone input 
on the 3G4010 for supervision of Tip/Ring connection. 

- Fire Alarms must be sent over both communication 

channels. Fire output from Fire Alarm Control Unit 
must be connected to the Input 1 on the 3G4010. 

- 24h Test Transmission must be enabled on the dialler 

and on the 3G4010. 

PSTN

 Figure 6 - DSC Subscribers’ Unit Fire and 3G Transmitter Mounted in the Same Room

Wiring Diagram for DSC Subscribers’ Unit Fire and 3G Transmitter

(Passive Communication System) 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

         

Fire Alarm 

Control Unit 

Outputs 

Fire

Supervisory 

Trouble 

DSC

Subscribers’ 

Unit Fire

Zone
Inputs

        TIP   

TIP            RING 

                 PGM1  

DSC Keypad 

LCD4501 

PK55XX

3G Wireless

Transmitter 

3G4010

T1/R1     
           TIP/RING 
Zone         
Input         PGM4 

AUX Power 
12V/700mA 

RM1C ULC 
Relay 

PC5003C
PC4050CR
cabinet

3G (HSPA)/2G (GPRS)   

PSTN

AC Input 

AC Input 

NOTES

:

- Power for 3G4010 must be provided from Fire 

Alarm Control Unit or separately listed power 
supply rated for the application (12V/700mA)  
(Jumper CON5 shall be on for Fire Monitoring).

- All wiring connections must be run in a protective conduit.
- Phone Line Monitoring (TLM) must be enabled. 

- Connect PGM4 output from 3G4010 (Trouble 

Conditions) to a zone input on the Subscriber Unit 
for supervision of the GSM Transmitter. 

- 24hr Test Transmission over phone line (PSTN) and 

3G4010 must be enabled.  

- Fire Alarms must be sent over both communication

 channels.  

- On the Subscribers’ Unit, program PGM1 for 

PC1616/PC1832/PC1864 as System Event (Section 
[009] as type 10; Section [501] Fire Event option 2 
ON). An alternate option is to program PGM1 as Zone
Follower (Sec [009] = 29) and assign Fire Zone to PGM1
in Section [551].  Ensure Bit 3 is on in [501]. In this case,
a restored fire alarm condition does not require the DSC
control panel to be reset.
For PC4020 program PGM1 as type 49 Steady Fire ([00070049]). 

  

- Dry contact outputs from ULC Listed Fire Alarm 

Control Unit must be connected to zone inputs on 
the ULC Listed DSC Subscribers’ Unit Fire.

  

PC4020 
PC1864 
PC1832 
PC1616

RM1C ULC 
Relay 

3G4010 cabinet 

- Phone Line trouble is indicated by Yellow LED on 3G4010. 

- Refer to detailed diagrams in Figure 7.

Содержание 3G4010

























Отзывы: