DriSteem GTS LX Series Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 88

background image

67

GTS HUMIDIFIER LX SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

REMOVAL OF THE SECONDARY HEAT EXCHANGER(S)

1.  Drain the humidifier tank.
2.  Follow the shut down procedure on page 60.
3.  Disconnect from the secondary heat exchanger(s):

•  Combustion air hoses
•  Combustion air vacuum line
•  Incoming water
•  Discharge water
•  Pressure equalization hose
•  Pressure switch
•  Temperature switch
•  Condensate p-trap

4. Remove the tri-clover clamp connecting the primary and secondary heat

exchanger(s).

5. Loosen the worm gear clamp on the stainless steel collar at the top of the

heat exchanger(s).

6. Remove eight bolts and nuts from the flange at the secondary heat

exchanger(s) flue gas outlet.

7. Remove the four nuts from the bracket securing the secondary heat

exchanger(s) to the primary tank, and allow it to drop free from the plastic
flue adapter.

MAINTENANCE

Inspection and maintenance:

REMOVAL OF THE PRIMARY HEAT EXCHANGER

1. Disconnect:

• Incoming gas line
• Water lines (at the primary tank secondary tank and Drain-kooler water

tempering device)

• Main drain line
• Component power connections (blower, ignition module and tank temp

sensor)

2.  Remove secondary heat exchanger. See instructions.
3.  Remove the water tempering device.
4.  Remove nuts around the perimeter of the heat exchanger face.
5.  Pull heat exchanger out horizontally

Note: Support the heat exchanger face once it is free of the studs.

6. Reverse this procedure to reassemble.

Note: Always install a new gasket when the heat exchanger is
reassembled.

Heat exchangers

«
...
67
68
69
70
71
...
»

Содержание GTS LX Series

























































































Отзывы:

Нет отзывов

Похожие инструкции для GTS LX Series

Бренд: B.Well Страницы: 18

Бренд: Levoit Страницы: 76

ELEKTRA health+

Бренд: S&P Africa Страницы: 5

Бренд: N'oveen Страницы: 9

Бренд: MEI Страницы: 28

Бренд: Clarke Страницы: 20

MDT1-10DMN3-QA3

Бренд: CO/Tech Страницы: 40

Бренд: CO/Tech Страницы: 72

Бренд: albert Страницы: 24

humiplus advanced

Бренд: miniland baby Страницы: 76

Бренд: Phoenix Страницы: 9

Бренд: Okoia Страницы: 40

Бренд: Phoenix Страницы: 8

Бренд: EUROM Страницы: 32

Бренд: Munters Страницы: 41

Бренд: Idylis Страницы: 14

Бренд: Fantech Страницы: 20

Бренд: Ultra-Aire Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды