DriSteem GTS LX Series Скачать руководство пользователя страница 18

Страница: 18 / 88

GTS HUMIDIFIER LX SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Optional floor stand mount (Models 50, 75,100, and 150 only)

FIGURE 16-1: LX SERIES FLOOR STAND MOUNT ASSEMBLY

FLOOR STAND MOUNTING INSTRUCTIONS

1.  Refer to Figure 17-1 for assembly of the floor stand.
2.  Use the hardware provided by DriSteem to assemble.
3.  Arrange appropriate lifting mechanism and personnel

to mount the GTS humidifier LX series on the floor
stand. See Warning below.

4. Use the lifting hole on the base of humidifier to

carefully lift it off the ground. See Warning below.

5. Slowly lower the humidifier on the floor stand.
6. Secure the base of the humidifier to the floor stand

using sheet metal screws.

OM-7972

OM-7971

Notes:

•

Weight of floor stand:

Models LX-50 - LX-100: 24 lbs (11 kg),

Model LX-150: 30 lbs (14 kg)

•

Allows for condensate piping/pump

•

Bottom supply water connection is located underneath the side

water connection. See fill valve connection position on page 13.

WARNING

HEAVY OBJECT

To avoid muscle strain or back injury, use lifting aids and
proper lifting techniques when removing or replacing.

Model LX-150

Models LX-50 - LX-100

Содержание GTS LX Series

























































































Результаты поиска

Содержание GTS LX Series

Отзывы:

Похожие инструкции для GTS LX Series

Бренды по названию

Популярные бренды

DriSteem GTS LX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GTS LX Series

Отзывы:

Похожие инструкции для GTS LX Series

Бренды по названию

Популярные бренды