DriSteem GTS LX Series Скачать руководство пользователя страница 56

Страница: 56 / 88

GTS HUMIDIFIER LX SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Sidewall venting (continued)

INSTALLATION

FIGURE 54-2: GTS HUMIDIFIER LX
SERIES SIDEWALL VENTING
WITH CONCENTRIC VENT

12" (305 mm)

Overhang or

roof

Grade/snow line

OM-7982

SIDEWALL INSTALLATION

See Figures 54-1 and Figures 54-2.

• For Models LX-50 - LX-300 only: Install a drip tee within the first 3' (1 m)

of flue venting for flue condensate removal. If flue vent is less than 10' (3

m) long and a sidewall exit, then no drip tee needed.

Warning:

Failure

to follow these instructions could reduce the service and efficiency of the

secondary heat exchanger.

• If total actual length of flue gas venting is less than 10' AND sidewall exit is

used, a tee is not needed.

• The combustion

air

piping must end in a down-turned elbow. This

arrangement avoids recirculation of flue products into the combustion air

stream.

• The flue gas

vent

piping may terminate in an elbow pointed outward or

away from the air inlet at least 12" (305 mm) above the combustion air

inlet, or use a tee as a termination to minimize effects of wind.

• The vent must end:

•  At least 6' (1.8 m) from adjacent walls.
•  No closer than 12" (305 mm) below roof overhang.
•  At least 3' (0.9 m) above any forced air intake within 10' (3 m).
•  No closer than 12" (305 mm) below or horizontally from any door or

window or any other gravity air inlet.

• Air inlet must be at least 12" (305 mm) above grade or snow line; at least

12" (305 mm) below the vent end; and the vent pipe must not extend

more than 24" (610 mm) vertically outside the building unless supports are

added.

FIGURE 54-1: GTS HUMIDIFIER LX SERIES SIDEWALL VENTING

OM-7981

12" (305 mm)

12"

(305 mm)

Bird screen

Flue gas vent

Combustion

air intake

Grade/snow line

Use a tee in high

wind areas

Bird screen

Maximum outside vent

piping length 24" (610 mm)

Содержание GTS LX Series

























































































Результаты поиска

Содержание GTS LX Series

Отзывы:

Похожие инструкции для GTS LX Series

Бренды по названию

Популярные бренды

DriSteem GTS LX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GTS LX Series

Отзывы:

Похожие инструкции для GTS LX Series

Бренды по названию

Популярные бренды