DriSteem GTS LX Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 88

background image

47

GTS HUMIDIFIER LX SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

GUIDELINES

• The GTS is a Fan Assisted Category IV (condensing, positive pressure)

Appliance.

• Maximum flue temperature is 140 °F (60 °C).
• Vent piping must be UL or UL/CSA listed PVC, CPVC, polypropylene or any

other vent type approved for a Category IV appliance.

• Follow supplier fitting and cement/primer instructions to ensure proper fit,

adhesion, and assembly.

• Clean and seal inlet piping per the pipe manufacturer's recommended

solvents and cements. Follow manufacturer's recommended procedures

for pipe and fitting preparation, cutting and attachment with appropriate

solvents and cements for the material.

•  Insulate sealed combustion piping to avoid dripping from condensation.
•  Do not use vent equipment from more than one application/manufacturer.
•  Do not insulate the flue vent piping.
•  Installation must be in accordance with Part 7, Venting of Equipment, of

the National Fuel Gas Code, ANSI Z223.1; or Section 7, Venting Systems

and Air Supply Appliances, of the CAN/CGA B149 Installation Codes; or

National Gas Safety Code (Installation & Use) Regulations (latest revision);

governing codes, and the vent manufacturer’s instructions.

General venting (continued)

Note:

For European models, contact your distributor

for horizontal venting parts.

INSTALLATION

WARNING

Installation requirements

The humidifier must be installed by
a qualified technician and meet the
requirements of all governing codes.
Failure to follow these instructions could
cause severe bodily injury or death.

WARNING

Installation requirements

Failure to properly seal all joints and
seams as required in the air inlet piping
may result in flue gas recirculation,
spillage of flue products and carbon
monoxide emissions causing sever
personal injury or death.

Table 47-1:
Approved PVC/CPVC flue gas vent pipe and fittings

Item

Vent material

United States

Canada

Piping

PVC

ANSI/STM D2665

IPEX system

1738

ULC S636

PVC, Sch. 40

ANSI/ASTM D1785

PVC, SDR series

ANSI/ASTM D2241

CPVC, Sch. 40

ANSI/ASTM F441

CPVC, SDR series

ANSI/ASTM F422

Fittings

PVC, DWV, Sch. 40

ANSI/ASTM D2665

PVC, Sch. 40

ANSI/ASTM 2466

PVC, Sch. 80

ANSI/ASTM 2467

CPVC, Sch. 40

ANSI/ASTM F438

CPVC, Sch. 80

ANSI/ASTM F439

Cement,

primer

PVC

ANSI/ASTM D2564

CPVC

ANSI/ASTM F493

Note: Do not use cellular (foam) core PVC, DWV pipe, ASTM F891, or cellular core CPVC or

RADEL (Polyphenylsulfone).

Table 47-2:
Approved vent manufacturers

Item

Manufacturer

Polypropylene

Centrotherm Eco Systems*
DuraVent (M&G Group)

Stainless steel

DuraVent (M&G Group)
Z-Flex
Heat Fab
Metal Fab
Security Chimney

* For 2", 3", and 4" vent pipe only.

«
...
47
48
49
50
51
...
»

Содержание GTS LX Series

























































































Отзывы:

Нет отзывов

Похожие инструкции для GTS LX Series

Бренд: Haier Страницы: 8

Бренд: Boneco Страницы: 44

Бренд: Therma-Stor Страницы: 11

Бренд: VADI Страницы: 29

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 14

CDAS HL 050 Series

Бренд: Parker Страницы: 398

Бренд: Heylo Страницы: 18

Бренд: Ecoair Страницы: 15

8000 Residential Steam Humidifier

Бренд: Johnson Controls Unitary Products Страницы: 44

Бренд: GUTFELS Страницы: 36

Бренд: camry Страницы: 42

SMTD-201710V2EP

Бренд: Seago Страницы: 16

Бренд: Sullair Страницы: 84

Бренд: Crane Страницы: 12

Бренд: Stadler Form Страницы: 56

Бренд: strex Страницы: 12

Comfortair 99324

Бренд: Trebs Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды