Dremel 4000, Оригинальное руководство пользователя

Страница: 23 / 92

23
forefinger. Its sleek shape has an excellent line of sight for
performing detailed etching, carving and engraving work.
This nose piece is not included in every kit. PICTURE 12
OPERATING SPEEDS
To select the right speed for each job, use a practice piece
of material.
SLIDE "ON/OFF" SWITCH
The tool is switched "ON" by the slide switch located on
the top side of the motor housing.
TO TURN THE TOOL "ON", slide the switch button
forward.
TO TURN THE TOOL "OFF", slide the switch button
backward.
HIGH PERFORMANCE MOTOR
Your tool is equipped with a high performance rotary tool
motor. This motor expands the versatility of the rotary tool
by driving additional Dremel attachments.
ELECTRONIC FEEDBACK
Your tool is equipped with an internal electronic feedback
system that provides a “soft start”, which will reduce the
stresses that occur from a high torque start. The system
also helps to keep the preselected speed virtually constant
between no-load and load conditions.
VARIABLE SPEED DIAL
Your tool is equipped with a variable speed dial. The
speed may be adjusted during operation by presetting the
dial on or between any one of the settings.
The speed of Rotary Tool is controlled by setting this dial
on the housing. PICTURE 13
Settings for Approximate Revolutions
Switch Setting Speed Range
5 5,000 RPM
10 10,000 RPM
*15 15,000 RPM
20 20,000 RPM
25 25,000 RPM
30 30,000 RPM
35 35,000 RPM
* Do not exceed 15,000 RPM when using wire brushes.
Refer to the Speed Settings chart on pages 4-7 to help
determine the proper speed for the material being worked
on and the accessory to use.
Most jobs can be accomplished using the tool at the
highest setting. However, certain materials (some plastics
and metals( can be damaged by high-speed generated
heat and should be worked on at relatively low speeds.
Low speed operation (15,000 RPM or less( is usually
best for polishing operations employing the felt polishing
accessories. All brushing applications require lower
speeds to avoid wire discharge from the holder. Let
the performance of the tool do the work for you when
using lower speed settings. Higher speeds are better for
hardwoods, metals and glass and for drilling, carving,
cutting, routing and shaping.
Some guidelines regarding tool speed:
• Plastic and other materials that melt at low
temperatures should be cut at low speeds.
• Polishing, buffing and cleaning with a wire brush must
be done at speeds no greater than 15,000 RPM to
prevent damage to the brush and your material.
• Wood should be cut at high speed.
• Iron or steel should be cut at high speed.
• If a high speed steel cutter starts to vibrate, it usually
indicates that it is running too slowly.
• Aluminium, copper alloys, lead alloys, zinc alloys and
tin may be cut at various speeds, depending on the
type of cutting being done. Use a paraffin (not water(
or other suitable lubricant on the cutter to prevent the
cut material from adhering to the cutter teeth.
NOTE: Increasing pressure on the tool is not the answer
when it is not performing properly. Try a different accessory
or speed setting to achieve the desired result.
MAINTENANCE
Preventive maintenance performed by unauthorized
personnel may result in misplacing of internal wiring
and components which could cause serious hazard. We
recommend that all tool service be performed by a Dremel
Service Facility. To avoid injury from unexpected starting or
electrical shock, always remove plug from wall outlet before
performing service or cleaning.
CLEANING
!
WARNING
TO AVOID ACCIDENTS, ALWAYS
DISCONNECT THE TOOL AND/OR
CHARGER FROM THE POWER
SUPPLY BEFORE CLEANING. The tool can be cleaned
most effectively with compressed dry air. Always wear
safety goggles when cleaning tools with compressed air.
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool
by inserting pointed objects through an opening.
!
WARNING
CERTAIN CLEANING AGENTS AND
SOLVENTS DAMAGE PLASTIC
PARTS. Some of these are: gasoline,
carbon tetrachloride, chlorinated cleaning solvents,
ammonia and household detergents that contain ammonia.
SERVICE AND WARRANTY
!
WARNING
NO USER SERVICEABLE PARTS
INSIDE. Preventive maintenance
performed by unauthorized personnel
may result in incorrect connection of internal wiring and
components which could cause serious hazard. We
recommend that all tool service be performed by a Dremel
Service Centre. SERVICEMEN: Disconnect the tool and/or
charger from the power source before servicing.
This DREMEL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling are
excluded from the warranty.
In case of a complaint, send the undismantled tool or
charger and proof of purchase to your dealer.
CONTACT DREMEL
For more information on the Dremel product range,
support and hotline, go to www.dremel.com.
This nose cap has an integrated wrench allowing you to
loosen and tighten the collet nut without the use of the
standard collet wrench.
1. Unscrew the nose cap from the tool, line-up the steel
insert on inside of the cap with the collet nut.
2. With the shaft lock engaged twist nose cap counter
clockwise to loosen the collet nut. Do not engage the
shaft lock button while multitool is running.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock engaged twist nose cap clockwise
to tighten the collet nut.
5. Screw the nose cap back into its original position.
NOTE: Be sure to read the instructions supplied with
your Dremel accessory for further information on its
use.
Use only Dremel tested, high performance accessories.
BALANCING ACCESSORIES
For precision work, it is important that all accessories
be in good balance (much the same as the tires on your
automobile(. To true up or balance an accessory, slightly
loosen collet nut and give the accessory or collet a 1/4 turn.
Re tighten collet nut and run the Rotary Tool. You should be
able to tell by the sound and feel if your accessory is running
in balance. Continue adjusting in this fashion until best
balance is achieved.
GETTING STARTED
USE
The first step in using the multitool is to get the "feel" of it.
Hold it in your hand and feel its weight and balance. Feel
the taper of the housing. This taper permits the tool to be
grasped much like a pen or pencil.
Always hold the tool away from your face. Accessories can
be damaged during handling and can fly apart as they come
up to speed.
When holding tool, do not cover the ventilation openings
with your hand. Blocking the ventilation openings could
cause the motor to overheat.
IMPORTANT! Practice on scrap material first to see how the
tool’s high-speed action performs. Keep in mind that your
multitool will perform best by allowing the speed, along with
the correct Dremel accessory and attachment, to do the
work for you. Do not put pressure on the tool during use,
if possible. Instead, lower the spinning accessory lightly to
the work surface and allow it to touch the point at which
you want to begin. Concentrate on guiding the tool over the
work using very little pressure from your hand. Allow the
accessory to do the work.
Usually it is better to make a series of passes with the tool
rather than to do the entire job with one pass. A gentle
touch gives the best control and reduces the chance of
error.
HOLDING THE TOOL
For best control in close work, grip the multitool like a
pencil between your thumb and forefinger. PICTURE 10
The "golf" grip method is used for heavier operations such
as grinding or cutting. PICTURE 11
Nose Piece
For performing precision tasks a separate nose piece is
available. It has a trilobular shape which allows the user
to pinch the nose piece comfortably between thumb and