Dolphin TCM 330 Скачать руководство пользователя страница 17

Страница: 17 / 62

F-710-017, V1.2 TCM 330 / TCM 330U User Manual | v1.1 | August 2016 | Page 17/62

USER MANUAL V1.1

TCM 330 / TCM 330U

Wireless LED Controller Module

3.5.6

Antenna

3.5.6.1

Overview

Several antenna types have been investigated by EnOcean. Please refer to our application

notes AN102, and AN105 which give an overview on our recommendations.

TCM330 (868.3 MHz) has been approved with whip antenna. Modules based on TCM 330

that are used in Europe do not need additional radio approval if the external antenna fulfils

the following requirements:

Frequency band

868.300 MHz ISM Antenna must be suited for this band

Antenna type

Passive

Mandatory for radio approval

Impedance

~50 Ohm

Mandatory for radio approval

Maximum gain

≤ 0 dBd

Mandatory for radio approval

In addition it is important to fulfill the following requirements in order to achieve compati-

bility with other EnOcean products and to ensure excellent EMI robustness:

VSWR

≤ 3:1

Important for compatibility with EnOcean protocol

Return Loss

> 6 dB

Important for compatibility with EnOcean protocol

Bandwidth

≤ 20 MHz

Important if 10 V/m EMI robustness required for device

TCM330U (902.875 MHz) is designed for use with the following antenna types:

EnOcean-defined whip antenna

EnOcean-defined helix antenna

Chip antenna Mitsubishi Material, Type AM11DG-ST01

TCM 330U is FCC / IC pre-approved (limited modular approval) for these antennas.

Please contact EnOcean for details.

Note that a full FCC / IC approval is needed if TCM 330U modules are used in US /

Canada with antennas other than these specified antennas.

Содержание TCM 330































































Результаты поиска

Содержание TCM 330

Отзывы:

Похожие инструкции для TCM 330

Бренды по названию

Популярные бренды

Dolphin TCM 330, Руководство пользователя

Результаты поиска

Содержание TCM 330

Отзывы:

Похожие инструкции для TCM 330

Бренды по названию

Популярные бренды