DOGA MDT Series Скачать руководство пользователя страница 80

Страница: 80 / 84

Instructions manual

/ MDT Series & MDTC38

60429 08/21

STANDARDS

15.1 Manufacturer details

Importer:

DOGA

Address:

ZA Pariwest

8 avenue Gutenberg CS 50510

78317 MAUREPAS CEDEX - FRANCE

15.2 Markings

MDT / MDTC Equipment name

Type

Equipment reference

Serial no.

Unique equipment serial number

Mm/yyyy

Equipment month/year of manufacture (first digits of the S/N)

Equipment designed and built in compliance with the requirements of European

directives 2006/42/EU and 2014/30/EU

All safety instructions and other instructions must be read

15.3 Transport and storage

Information

Your equipment may be damaged if you transport or store it in unsuitable conditions.

Comply with the transport and storage information for your equipment.

Transport

Use a container suitable for the transport of the equipment in order to protect it from external

influences.

Comply with the following instructions before each transport:

⚫

Shut down the device

⚫

Disconnect the power supply cord

Storage

Comply with the following instructions before storing:

⚫

Shut down the device

⚫

Disconnect the power supply cord

⚫

Clean the device following the indications in the Maintenance section.

⚫

Store it in a suitable container to protect it from dust and exposure to direct sunlight.

⚫

Store it in a dry location at a temperature below 40°C.

Содержание MDT Series





















































































Результаты поиска

Содержание MDT Series

Отзывы:

Похожие инструкции для MDT Series

Бренды по названию

Популярные бренды

DOGA MDT Series, Инструкция по эксплуатации

Результаты поиска

Содержание MDT Series

Отзывы:

Похожие инструкции для MDT Series

Бренды по названию

Популярные бренды