DOGA MDT Series Скачать руководство пользователя страница 6

Страница: 6 / 84

Instructions manual

/ MDT Series & MDTC38

60429 08/21

Remove adjusting keys or switches before turning the tool on.

A wrench or a key that is left

attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.

Proper footing and balance

enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard

hat, or hearing protection must be used for appropriate conditions.

1.4 Tool use and Care

Use clamps or other practical way to secure and support the workplace to a stable
platform.

Holding the work by hand or against your body is unstable and may lead to loss of

control.

Do not force tool. Use the correct tool for your application.

The correct tool will do the job

better and safer at the rate for which it is designed.

Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool.

Such preventive safety

Store idle tools out of reach of children and other untrained persons.

Tools are dangerous

in the hands of untrained users.

Maintain tools with care

Keep cutting tools sharp and clean.

Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tools operation.

If damaged, have the tool serviced before

using.

Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on another
tool.

1.5 Service

Tool service must be performed only by qualified personnel.

Service or maintenance

performed by unqualified personnel could result in a risk of injury

When servicing a tool, use only identical replacement parts.

Follow instructions in

the Maintenance section of this manual.

Use of unauthorized parts or failure to follow

Maintenance instructions may create a risk of electric shock or injury.

1.6 Specific safety rules

Hold tool by insulated gripping surfaces when performing an operation where the cutting
tool may contact hidden wiring or its own cord.

Contact with a "live" wire will make exposed

metal parts of the tool "live" and shock the operator.

Never lubricate aerosol oil on to the electrical part.

Содержание MDT Series





















































































Результаты поиска

Содержание MDT Series

Отзывы:

Похожие инструкции для MDT Series

Бренды по названию

Популярные бренды

DOGA MDT Series, Инструкция по эксплуатации

Результаты поиска

Содержание MDT Series

Отзывы:

Похожие инструкции для MDT Series

Бренды по названию

Популярные бренды