DNP CL-500, Руководство по обслуживанию

Страница: 25 / 60

21
TROUBLESHOOTING
17 Cannot enter Cleaning
Mode
HR is too hot!
18 Operation error in
EEPROM
EEPROM SUM Err
19 Turn over unit error
Mech Err(Flip)
20 Maintenace door upon
the tur n over unit is
onpen
Door Open(Flip)
21 No response from the
turn over unit
EXT.Com(No Rsp)
22 Communication eroor
with the turn over unit
EXT.Com(Rsp Err)
23 Illegal command from
upper laminator
Com Err CE(Flip)
24 Communication erorr
with lower laminator
Com Err RE(Flip)
25 No response from lower
laminator
Com Err NR(Flip)
No. Error Content/Text Displayed
Error Detection Action Parts to be replaced
Heat roller temperature is detected
with the heat roller thermostat.
The heat roller temperature
exceeds 50˚C during Cleaning
Mode.
EEPROM sum data cannot be
read normally, when the power on.
It does not return to the original
position even after ** seconds
during turning.
Inter lock switch is detected.
Unable to communicate with the
turn over unit.(No response)
Unable to communicate with the
turn over unit. (Unusual dada)
Unable to communicate with the
turn over unit. (Unusual dada or
the turn over unit is detected erorr)
Unable to communicate with the
turn over unit between the lower
laminator. (Unusual dada)
Unable to communicate with the
turn over unit between the lower
laminator. (No responce)
If the error occurs when the heat
roller temperature is below 50˚C,
this may be a thermostat error.
Measure the resistance value of the
thermostat. If the error occurs when
the thermostat resistance value is
normal, it may be a main board or
connection cable error.
Update the firmware version to
“017” or later.
Refer to the turn over unit manual.
Refer to the turn over unit manual.
C h e c k t h e s c r e w o f t h e
maintenance door is tightened.
Refer to the card turn over unit
manual.
C h e ck t h e c o n n e c t e d s t a t e
between the laminator and turn
over unit.
Refer to the card turn over unit
manual.
Check the connected state between
the laminator and turn over unit.
Refer to the card turn over unit
manual.
C h e ck t h e c o n n e c t e d s t a t e
between the laminator and turn
over unit.
Refer to the card turn over unit
manual.
C h e ck t h e c o n n e c t e d s t a t e
between the lower laminator and
turn over unit.
Refer to the card turn over unit
manual.
Check the lower laminator power on.
C h e ck t h e c o n n e c t e d s t a t e
between the lower laminator and
turn over unit.
Thermostat, or main board, or
connection cable.
When the EEPROM SUM Err is still
appear, replace the main board.
Refer to the turn over unit manual.
Refer to the turn over unit manual.
Inter lock switch board of the card
turn over unit or main board of the
card turn over unit.
Refer to the turn over unit manual.
Connection cable between the
laminator and turn over unit, or
main board of the laminator and
turn over unit.
Refer to the turn over unit manual.
Connection cable between the
laminator and turn over unit, or
main board of the laminator and
turn over unit.
Refer to the turn over unit manual.
Connection cable between the
laminator and turn over unit, or
main board of the laminator and
turn over unit.
Refer to the turn over unit manual.
Connection cable between the
lower laminator and turn over unit,
o r m a i n b o a r d o f t h e l ow e r
laminator and turn over unit.
Refer to the turn over unit manual.
Connection cable between the
lower laminator and turn over unit,
o r m a i n b o a r d o f t h e l ow e r
laminator and turn over unit.
<NOTE> No.18 to No.25 is indicate when card turn over unit (will be release in future) are connected.