background image

DLM-4 ZONE

DLM-4 ZONE

Controller

Controller

 30

 31

8. General Information
8.1 Warranty

WARRANTY

RETURNS

RETOURS

Dutch Lighting Innovation only uses high quality components. 
Under normal operating conditions, the mechanical and electronic 
components are covered by a three-year warranty from the original 
date of purchase. For service return the DLM-4 Zone Controller in the 
original packaging to your shop with the original sales receipt. 
Components that are excluded from warranty are components that 
have failed due to abnormal usage.
In the case of defects of the DLM-4 Zone Controller, the Controller will 
either be replaced or repaired using new or reconditioned products or 
parts. If the Controller will be replaced this limited warranty shall apply 
to the replacement product for the remaining initial warranty period, 
i.e. (three) 3 years from the date of purchase of the original product.

All returns need to be done in the original packaging in order to avoid 
damages of the product during transport. Defective products need 
to be returned to factory or service shop for repaiir. Non-professionals 
Do not open the cabinet to prevent electric shock or damage to the 
equipment

Pour tout retour, le produit doit être replacé dans son emballage 
d’origine afin d’éviter qu’il soit endommagé pendant le transport. 
Les produits défectueux doivent être renvoyés à l’usine ou à l’atelier 
d’entretien pour réparation. Avis aux non professionnels : n’ouvrez pas 
l’armoire afin d’éviter tout risque de choc électrique ou de dommages 
matériels.

8.2 Register your Controller for 
the Latest Software Updates

Dutch Lighting Innovations will occasionally release updated firmware 
for the DLM-4 Zone Controller. 

By registering your DLM-4 Zone Controller on our website 

www.dutchlightinginnovations.com

 we can notify you when an 

update is available.

We will not sell, rent or share your personal information. 

Содержание DLM-4 ZONE




















Отзывы: