background image

DLM-4 ZONE

DLM-4 ZONE

Controller

Controller

 18

 19

7.5 Zone Status Page

Once the DLM-4 Zone Controller has been installed and all settings 
have been entered, the DLM-4 Zone Controller will constantly monitor 
the air temperatures, ballast status and current Day or Night status 
within each of the lighting zones. 

The measured temperatures are displayed on the Zone status menu 
which also displays the current status of the DLM-4 Zone Controller 
controlled zones.

The Zone Status menu will be displayed unless there is an event / 
error that occurred. If an event is being displayed, pressing Enter will 
acknowledge the event / error, and reset the event log.

Pressing the Menu button from the Zone Status menu will access the 
Main menu. 

*NOTE: 

When one temperature sensor is assigned to more than one 

zone, that temperature sensor will display it’s information within ALL 
zones that it is assigned to.

7.6 Temperature Min-Max Page

Pressing the Find button on the DLM-4 Zone Controller will access 
some important functions. The first page that will be displayed is the 
Temperature Minimum-Maximum page.
Each of the temperature sensors installed will constantly measure the 
temperature and record the maximum (high) and minimum (low) 
temperatures. 
These recorded temperatures can be used to confirm that the cooling 
/ heating systems inside the growing area are working properly. 
The Min-Max recorded values will also verify that the growing area was 
not subjected to damaging high temperatures above the DLM-4 Zone 
Controllers dimming setpoints.
Once the recorded values have been viewed, the user can easily reset 
the values (each day) by pressing the Enter button. Pressing Enter will 
rest the recorder values and begin to store new values that can be 
viewed the next “day”. 

03/08/2017

Zone 1

Restrike

Zone 2

Restrike

Zone 3

Restrike

Zone 4

Restrike

1000W

67.2F

09:03

---.-F

09.03

---.-F

09:03

---.-F

09:03

ENTER to Reset

Zone 1

Zone 2

Zone 3

Zone 4

Max

Min

Max

Min

Max

Min

Max

Min

F

F

F

F

F

F

F

F

68.1

66.9

---.-

---.-

---.-

---.-

---.-

---.-

Содержание DLM-4 ZONE




















Отзывы: