background image

9024-065-Q-8-16

6

UL 325 Entrapment Protection

Class I - Residential
Vehicular Gate Operator

Entrapment Protection Types

Class II

 - Commercial/General Access

Vehicular Gate Operator

Class III - Industrial/Limited Access
Vehicular Gate Operator

Class IV -
Restricted Access
Vehicular Gate Operator

A vehicular gate operator (or system) intended for use in garages 
or parking areas associated with a residence of one-to four single 
families.

A vehicular gate operator (or system) intended for use in a 
commercial location or building such as a multi-family housing 
unit (five or more single family units), hotel, garages, retail store, 
or other buildings accessible by or servicing the general public.

A vehicular gate operator (or system) intended for use in an 
industrial location or building such as a factory or loading dock 
area or other locations not accessible by or intended to service 
the general public.

A vehicular gate operator (or system) intended for use in a 
guarded industrial location or building such as an airport security 
area or other restricted access locations not servicing the general 
public, in which unauthorized access is prevented via supervision 
by security personnel.

Gate Operator Category

UL 325 Classifications

Type A

  - Inherent entrapment protection system.

Type B1

 - Non-contact sensor (photoelectric sensor or the equivalent). 

Type B2

 - Contact sensor (edge device or equivalent). 

Type C

  - Inherent force limiting, inherent adjustable clutch or inherent pressure relief device.

Type D

  - Actuating device requiring constant pressure to maintain opening or closing motion of the gate.

*

 B1 and B2 means of entrapment protection must be MONITORED.

Vertical Barrier Note:

 Barrier gate operators (arm) 

that is not intended to move toward a rigid object 
closer than 16 inches (406 mm) are not required to 
be provided with a means of entrapment protection.

STATE PRISON

Horizontal Slide, Vertical Lift, Vertical Pivot

Swing, Vertical Barrier (Arm)

A, B1*, B2* or D

A, B1*, B2*, C or D

Effective January 12, 2016

Authorized

Personnel ONLY

Содержание 9024-080











































Отзывы: