background image

1

2

2

maINTeNaNCe

39

Battery

the mower is equipped with a maintenance free 
battery and does not need servicing. However, 
periodic charging of the battery with an automotive 
type battery charger will extend its life.
•  Keep battery and terminals clean.
•  Keep battery bolts tight.
•  See chart for charging times.

IMPORTANT INFORMATION
Do not attempt to open or remove caps or 
covers. Adding or checking level of electrolyte 
is not necessary.
Always use two wrenches for the terminal 
screws.

WARNING!
Do not short battery terminals by 
allowing a wrench or any other object to 
contact both terminals at the same time. 
Before connecting battery, remove metal 
bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected 
first to prevent sparks from accidental 
grounding.

Cleaning battery and terminals

Corrosion and dirt on the battery and terminals can 
cause the battery to lose power.
1.  Open the terminal access doors.
2.  Disconnect BLACK battery cable first, then the 

ReD battery cable and remove the battery from 
the machine.

3.  Rinse the battery with plain water and dry.
4.  Clean terminals and battery cable ends with wire 

brush until shiny.

5.  Coat terminals with grease or petroleum jelly
6.  Reinstall battery.

Replacing battery

1.  Lift seat and rotate forward.
2.  Open terminal access doors
3.  Using two ½" wrenches disconnect BLACK 

battery cable then ReD battery cable.

4.  Using a 

7

/

16

 wrench, remove the bolts on either 

side of the terminal guard and lift off guard.

5.  Carefully remove the battery from the mower.
6.  Install new battery with terminals in the same 

position as the old battery.

7.  Reinstall battery terminal guard.
8.  First connect ReD battery cable to positive (+) 

battery terminal with hex bolt and hex nut.

9.  Connect BLACK grounding cable to negative (-) 

battery terminal with remaining hex bolt and hex 
nut.

10.  Close access doors.
11.  Lower seat.

8066-049

1. terminal guard
2. Access doors

Battery cleaning and installation

CAUTION!
Always wear eye protection when 
around batteries.

StAnDARD

BAtteRY

StAte

OF

CHARGe

APPROXIMAte BAtteRY CHARGInG tIMe* 

tO FULL CHARGe At 80

O

F / 27

O

C

Maximum Rate at:

50 Amps

30 Amps

20 Amps

10 Amps

12.6V

100%

 - FULL CHARGe -

12.4V

75%

20 min.

35 min.

48 min.

90 min.

12.2V

50%

45 min.

75 min.

95 min.

180 min.

12.0V

25%

65 min.

115 min.

145 min.

280 min.

11.8V

0%

85 min.

150 min.

195 min.

370 min.

*Charging time depends on battery capacity, 

condition, age, temperature and efficiency of charger

Содержание DX152





































































Отзывы: