Dixon DX152 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 68

background image

OPeRaTION

33

Operating on Hills

Read the Safety Instructions

Driving on Slopes

in the

Safety

section.

WARNING!
Do not drive up or down hills with slopes
greater than 10 degrees. Do not drive
across slopes.

8066-052

Release the parking brake to restart movement

8066-054

Place controls in neutral position

• to restart movement, release the parking brake.
• Pull the control levers back to the center of the

mower and press forward to regain forward
motion.

• Make all turns slowly.

• the slowest speed possible should be used

before starting up or down hills.

• Avoid stopping or changing speed on hills.
• If stopping is absolutely necessary, pull drive

levers into the neutral position and push to the
outside of the unit and engage the parking brake.

«
...
31
32
33
34
35
...
»

Содержание DX152





































































Отзывы:

Нет отзывов

Похожие инструкции для DX152

Бренд: Yard Machines Страницы: 20

Бренд: Troy Built Страницы: 44

Бренд: Poulan Pro Страницы: 52

Бренд: Cub Cadet Страницы: 19

Бренд: Sears Страницы: 60

Бренд: AL-KO Страницы: 652

Бренд: Jacobsen Страницы: 62

2261ADC Articulator

Бренд: Lastec Страницы: 67

TECHline NEXTTECH L X4

Бренд: ZCS Страницы: 42

Бренд: Agri-Fab Страницы: 24

COLLECTOR 53 SE COMBI 53 SE COMBI

Бренд: Stiga Страницы: 2

Zero Turn Radius Mower

Бренд: Country Clipper Страницы: 25

Бренд: MTD Страницы: 35

Бренд: GGP ITALY Страницы: 176

Бренд: NEISEN Страницы: 17

Бренд: Maruyama Страницы: 76

Бренд: Grillo Страницы: 44

Бренд: Bush Hog Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды