Dixon DX152 Скачать руководство пользователя страница 53

Страница: 53 / 68

TROUblesHOOTING GUIDe

Problem

Cause

Machine vibrates

•

Blades are loose

•

Blades are incorrectly balanced

•

Blades are bent

•

engine is loose

engine overheats

•

Clogged air intake or cooling fins

•

engine overloaded

•

Poor ventilation around engine

•

Defective engine speed regulator

•

too little or no oil in the engine

•

Fouled spark plug

Battery not charging

•

Poor contact with battery terminal cable connectors

•

Charging lead is disconnected

•

Fault in engine charging system

Machine moves slowly, unevenly, or not at all

•

Parking brake on

•

Bypass valve on pump open

•

Drive belt for the transmission gears slack or has come off

•

Air in hydraulic system

Mower deck not engaging

•

Drive belt for the mower deck has come loose

•

Contact for the electromagnetic coupling has loosened

•

the blade switch is faulty or has come loose, from the cable
contact

•

the fuse has blown

Hydraulic drive leaks oil

•

Damaged seals, housing, or gaskets

•

Air trapped in hydraulic system

Uneven mowing results

•

Unequal tire pressure on the left and right sides

•

Blades are bent

•

Suspension for the mower deck is uneven

•

Blades are dull

•

Driving speed too high

•

the grass is too long

•

Grass collected under the mower deck

Содержание DX152





































































Результаты поиска

Содержание DX152

Отзывы:

Похожие инструкции для DX152

Бренды по названию

Популярные бренды

Dixon DX152, Руководство оператора

Результаты поиска

Содержание DX152

Отзывы:

Похожие инструкции для DX152

Бренды по названию

Популярные бренды