Dixon DX152 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 68

background image

maINTeNaNCe

42

Pump Belt

the belts are not adjustable. Replace belts if they
begin to slip from wear.

Replacing Pump Belt

Park the mower on a level surface. engage the
parking brake.

Belt Removal

From the top side of the deck:
1. Remove the deck belt (see

Deck Belt Removal

in

this section of the manual).

2. tilt seat forward to access fan covers. Remove

both fan covers.

8058-064

Remove fan covers

11. Adjust belt tension by turning the eyebolt until

there is approximately

7

/

8

" -1" of threads showing

outside the nut.

12. Belt tension should be set to 60-70 lbs.
13. Replace belt shields on both mandrel housings

and secure with fasteners.

14. Replace foot plate.

8065-054

Adjust belt tension

«
...
40
41
42
43
44
...
»

Содержание DX152





































































Отзывы:

Нет отзывов

Похожие инструкции для DX152

Бренд: Baroness Страницы: 5

Бренд: P.Lindberg Страницы: 47

Бренд: Toro Страницы: 52

Бренд: YAT Страницы: 41

MULTICLIP MULTICLIP 46 S SVAN

Бренд: Stiga Страницы: 2

Бренд: MTD Страницы: 20

Бренд: Yardworks Страницы: 35

Бренд: Yard-Man Страницы: 42

Бренд: Simplicity Страницы: 14

Бренд: Worldlawn Страницы: 14

Бренд: GGP ITALY SPA Страницы: 72

Бренд: Qualcast Страницы: 22

Smart Speed 569

Бренд: Troy-Bilt Страницы: 20

Бренд: MTD Страницы: 47

Бренд: Parkside Страницы: 52

Greensplex 160 898850

Бренд: Ransomes Страницы: 36

Бренд: Garden Gear Страницы: 16

Бренд: MTD Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды