Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 95

background image

72

© 2 0 0 7 D i r e c t e d E l e c t r o n i c s

The remote start will not activate.

Check to ensure that the hood is not open and that the brake
pedal is not depressed. Check harnesses and connections. Make
sure the harnesses are fully plugged into the remote start module.
Make sure there are good connections to the vehicle wiring. Check
voltage and fuses. Use a meter and check for voltage between the
RED wire and the BLACK ground wire. If you have less than battery
voltage, check both 30A fuses on the main power wires. Also make
sure that the ground wire is going to a good paint-free chassis
ground.

The remote start will activate but the starter never engages.

1. Check for voltage on the YELLOW starter wire two seconds

after the remote start becomes active. If there is voltage
present, skip to Step 4. If there is no voltage present,
advance to Step 2.

2. Check the 30A fuses.

3. Does the vehicle have an immobilizer? Some Immobilizer

systems will not allow the vehicle to crank if active.

4. Check connections. The two PINK heavy gauge input

wires

should have solid connections. "T-taps", or "scotch locks" are
not recommended for any high current heavy gauge wiring.
Also, if the vehicle has more than one 12-volt input wire,
then connect one PINK wire to each.

➜

➜

«
...
69
70
71
72
73
...
»

Содержание READY REMOTE 24927
































































































Отзывы:

Нет отзывов

Похожие инструкции для READY REMOTE 24927

Бренд: Daikin Страницы: 38

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 148

Бренд: Waeco Страницы: 20

Бренд: Z-Wave Страницы: 56

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

SHERPA MONOBLOC B0812

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 16

Бренд: PURSUIT Страницы: 24

Бренд: Quasar Страницы: 4

Бренд: Gira Страницы: 7

Бренд: Control 4 Страницы: 2

Бренд: Clicker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды