Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 95

background image

27

© 2 0 0 7 D i r e c t e d E l e c t r o n i c s

Step 3, H3

Door Lock Connections

There are eight different types of door lock systems (Type A - H).
Refer to the vehicle-specific wiring instructions on the web and
the chart below to help determine which door lock system your
vehicle uses. On some late model GM vehicles a door lock data
interface module may be required.

Type A: Three-wire (+) pulse controlling factory lock relays.

Type B: Three-wire (-) pulse controlling factory lock relays.

Type C: Direct-wired reversing-polarity switches. The switches are
wired directly to the motors. This type of system has no factory
relays. Relays (not included) will be required for this type of door
lock system.

Type D: Adding one or more aftermarket actuators. These include
slave systems without an actuator in the driver's door, but with
factory actuators in all the other doors.

Type E: Electrically-activated vacuum systems.

Type F: One-wire system - cut to lock, ground to unlock.

This is a very rare system found mainly in early 90's imports

Type G: Positive (+) multiplex. One wire controls lock and unlock
using resistor(s).

Type H: Negative (-) multiplex. Same as type G system, but uses
(-) pulse instead.

Note!

From the factory, your system is set up for Type

B (-) door locks. To change your door lock outputs to
Type A (+), simply use the wires in the opposite con-
figuration. You will now have (+) door locks.

«
...
24
25
26
27
28
...
»

Содержание READY REMOTE 24927
































































































Отзывы:

Нет отзывов

Похожие инструкции для READY REMOTE 24927

Бренд: Omegalink Страницы: 2

Бренд: Prestige Страницы: 4

Ungo ProSecurity RS10

Бренд: Clarion Страницы: 19

MERLIN BLUE BUTTON

Бренд: EAST COAST Страницы: 2

CLIK64-M Series

Бренд: Active Control Technology Страницы: 2

Бренд: TANDBERG Страницы: 2

Бренд: Vulcan-Hart Страницы: 12

Бренд: Eurgle Страницы: 31

Бренд: Spektrum Страницы: 17

Бренд: Sonnenkonig Страницы: 3

Бренд: Interlink electronics Страницы: 12

ExpressCard Media Remote for Bluetooth

Бренд: Interlink electronics Страницы: 24

Бренд: Planet Страницы: 16

Бренд: Westfalia Страницы: 18

Бренд: Westfalia Страницы: 26

Wetecom 99 67 36

Бренд: Westfalia Страницы: 27

Бренд: Black Widow Security Страницы: 12

Бренд: Viessmann Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды