Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 95

background image

24

© 2 0 0 7 D i r e c t e d E l e c t r o n i c s

Parking Light Flash

There are several different types of parking light circuits. The
following description is for a standard positive-triggered parking-
light circuit only. If the web vehicle information suggests a (-)
parking light circuit, the fuse jumper (on the side of the module)
must be moved to the opposite position.

A red 10 amp mini-fuse is included in a small plastic bag inside
the packaging. THIS FUSE MUST BE INSERTED FOR THE PARKING
LIGHTS TO WORK!

Using the web information on the vehicle, locate the suspected
wire. Connect the black multimeter lead to ground in the kick
panel. Probe the suspected wire with the red lead of your meter.
With the switch in the off position the multimeter should read 0
volts. While watching the multimeter, turn your headlight switch
to the parking light position. The multimeter should read 12 volts.

While testing the suspected wire, run the dash dimmer light
control up and down. The voltage should NOT vary. If the voltage
does vary, then this is the wrong wire. Continue probing to find
the correct wire.

Once you have identified the correct wire, solder the small YELLOW
wire of the 6-pin harness to it and wrap the connection with elec-
trical tape. If your light circuit tests the opposite position, you
most likely have a (-) parking light circuit.

Important!

Remember this description is for a (+)

parking light circuit. A (-) circuit will test differently.
Also, if the web information requires using resistors
for parking lights, contact Technical Support.

«
...
21
22
23
24
25
...
»

Содержание READY REMOTE 24927
































































































Отзывы:

Нет отзывов

Похожие инструкции для READY REMOTE 24927

Бренд: jablotron Страницы: 2

Бренд: Yaber Страницы: 52

Бренд: NAD Страницы: 4

Бренд: NAD Страницы: 4

Бренд: Insignia Страницы: 2

Бренд: DSEGenset Страницы: 74

Бренд: Broadcast Tools Страницы: 39

BLUETOOTH MEDIA REMOTE

Бренд: Targus Страницы: 24

Бренд: Hama Страницы: 16

Бренд: IC Dynamics Страницы: 18

Бренд: Chamberlain Страницы: 4

Бренд: IC Dynamics Страницы: 6

Бренд: Spectravision Страницы: 8

Бренд: Spectravision Страницы: 12

Бренд: Panasonic Страницы: 1

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды