Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 83

Страница: 83 / 95

Auto-rearming feature

Auto-rearming is designed to protect the vehicle in case of unin-
tended disarming of the alarm.

It will automatically re-arm the alarm and lock the doors 120
seconds after any transmitter disarm occurs.

To stop Auto-rearm, open a door or turn the ignition on before the
120 seconds expires.

Alarm Input Operations

When armed, the alarm has 6 inputs which can cause a full alarm
trigger output. Refer to the Alarm Diagnostic section for addi-
tional detail.

➤

The Door, Hood, Ignition and Brake inputs will cause an
immediate full trigger output when activated.

➤

The Sensor inputs can cause two types of outputs;
Warn-away and Full Trigger.

Alarm Trigger Outputs

➤

Warn-away output: this output consists of 5 chirps of
the Horn/Siren output and 3 flashes of the parking
lights.

➤

Full Trigger output: this output consists of flashing the
Parking lights and the Horn/Siren output for 30 seconds
followed by a 5 second pause to monitor the alarm
inputs. If an alarm input is still active the output will
repeat.

Note!

An optional two-stage sensor (p/n 504d) is

required for the Sensor outputs to activate. Call
Technical Support for more information on compatible
sensors.

Содержание READY REMOTE 24927
































































































Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды

Directed Electronics READY REMOTE 24927, Руководство по установке владельца

Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды