Directed Electronics READY REMOTE 24927 Скачать руководство пользователя страница 42

Страница: 42 / 95

of insulation off the tachometer wire in the vehicle and solder the
green tachometer input wire to it. Then wrap the connection with
electrical tape.

LEARNING YOUR TACH SIGNAL

If using a tach wire, you must learn the tach signal after com-
pleting the installation.

To learn tach signal:

1. Start car with key.

2. Wait about 5 seconds for the engine to idle down.

3. Press and hold the Momentary switch (about 10

seconds).

4. Tach learned: After a few seconds the LED will flash 2

times and turn on. Continue to hold the switch for 2 - 3
seconds and release.

5. Tach not learned: The LED will not turn on and will flash

3 times when the momentary switch is released. Check
the connections and try again.

Note!

If using a tach signal, the tach signal MUST

be learned before using the remote starter.

Содержание READY REMOTE 24927
































































































Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды

Directed Electronics READY REMOTE 24927, Руководство по установке владельца

Результаты поиска

Содержание READY REMOTE 24927

Отзывы:

Похожие инструкции для READY REMOTE 24927

Бренды по названию

Популярные бренды